Black & Decker XTC12IK, Руководство пользователя

Страница: 5 / 64

5
ENGLISH
Fitting and removing a screwdriver bit (fig. C)
◆
Pull the sleeve (3) forward.
◆
Insert the bit shaft into the sleeve as far as it will go.
◆
Release the sleeve to secure the bit.
◆
To remove the bit, pull sleeve forward and pull the bit out
firmly.
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (fig. A)
The battery needs to be charged before first use and whenever
it fails to produce sufficient power on jobs that were easily
done before. When charging the battery for the first time, or
after prolonged storage, it will only accept an 80% charge.
After several charge and discharge cycles, the battery will
attain full capacity. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
◆
To charge the battery (4), remove it from the tool and
insert it into the charger (5). The battery will only fit into
the charger in one way. Do not force. Be sure that the
battery is fully seated in the charger.
◆
Plug in the charger.
◆
Check if the red charging indicator (6) lights up. If the
green end of charge indicator (7) lights up now instead,
the battery is too hot and cannot be charged. If this
happens, remove the battery from the charger, let the
battery cool down for approx. 1 hour and re-insert it.
After approx. 30 minutes of charging, the red charging
indicator (6) will stop lighting and the green end of charge
indicator (7) will light up. The battery is now fully charged.
◆
Remove the battery from the charger.
Selecting the direction of rotation (fig. D)
For tightening screws, use forward (clockwise) rotation.
For loosening screws, use reverse (counterclockwise) rotation.
◆
To select forward rotation, push the forward/reverse
slider (2) to the left.
◆
To select reverse rotation, push the forward/reverse slider
to the right.
◆
To lock the tool, set the forward/reverse slider into the
centre position.
Screwdriving
◆
Select forward or reverse rotation using the forward/
reverse slider (2).
◆
To switch the tool on, press the switch (1). The tool speed
depends on how far you press the switch.
◆
To switch the tool off, release the switch.
Hints for optimum use
◆
Always use the correct type and size of screwdriver bit.
◆
If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
◆
Always hold the tool and screwdriver bit in a straight line
with the screw.
Maintenance
Your Black & Decker tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
◆
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
◆
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.