Black & Decker XTC12IK, Руководство пользователя

Страница: 4 / 64

4
ENGLISH
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed.
Use of the power tool
for operations different from those intended could result
in a hazardous situation.
5. Battery tool use and care
a. Ensure the switch is in the off position before
inserting battery pack. Inserting the battery pack into
power tools that have the switch on invites accidents.
b. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
c. Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
d. When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
e. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help.
Liquid ejected from
the battery may cause irritation or burns.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions for batteries and chargers
Batteries
◆
Never attempt to open for any reason.
◆
Do not expose the battery to water.
◆
Do not store in locations where the temperature may
exceed 40 °C.
◆
Charge only at ambient temperatures between 4 °C and
40 °C.
◆
Charge only using the charger provided with the tool.
◆
When disposing of batteries, follow the instructions given
in the section “Protecting the environment”.
◆
Under extreme conditions, battery leakage may occur.
When you notice liquid on the battery, proceed as follows:
- Carefully wipe the liquid off using a cloth.
Avoid skin contact.
- In case of skin or eye contact, follow the instructions
below.
Warning! The battery fluid, a 25-30% solution of potassium
hydroxide, can be harmful. In case of skin contact, immediately
rinse with water. Neutralise with a mild acid such as lemon
juice or vinegar. In case of eye contact, rinse abundantly with
clean water for at least 10 minutes. Consult a physician.
◆
Do not incinerate the battery.
◆
Do not attempt to charge damaged batteries.
Chargers
◆
Use your Black & Decker charger only to charge the battery
in the tool with which it was supplied. Other batteries
could burst, causing personal injury and damage.
◆
Never attempt to charge non-rechargeable batteries.
◆
Have defective cords replaced immediately.
◆
Do not expose the charger to water.
◆
Do not open the charger.
◆
Do not probe the charger.
The charger is intended for indoor use only.
Electrical safety
Your charger is double insulated; therefore no earth
wire is required. Always check that the mains
voltage corresponds to the voltage on the rating
plate. Never attempt to replace the charger unit with
a regular mains plug.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Bit holder
4. Battery
Fig. A
5. Charger
6. Charging indicator
7. End of charge indicator
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battery (fig. B)
◆
To fit the battery (4), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
◆
To remove the battery, push the release button (8) while
at the same time pulling the battery out of the receptacle.