Black & Decker PW2100, Оригинальное руководство пользователя

Страница: 23 / 27

ENGLISH • 23
TECHNICAL INFORMATION
ENVISAGED USE
This appliance has been designed for individual use for
the cleaning of vehicles, machines, boats, masonry, etc, to
remove stubborn dirt using clean water and biodegradable
chemical detergents.
Vehicle enginesmay be washed only if the dirty water is
disposed of as per regulations in force.
f
Intake water temperature: See data plate on
the appliance.
f
Intake water pressure: Below 10 bar.
f
Operating ambient temperature: Above 0 °C.
The machine complies with the IEC.
OPERATOR
The symbol on the front cover identifies the appliance’s
intended operator (professional or non-professional).
MAIN COMPONENTS (Fig. A)
The machine is delivered partially disassembled
in a carton.
1. Adjustable spray nozzle
2. Lance
3. Gun with safety catch
4. Power supply cable with plug
5. High pressure hose
6. Detergent tank
7. Quick Connector
8. Nozzle cleaning tool
9. Handle
10. Hose reel
Caution! Safety devices: Do not tamper with
or adjust the safety valve setting.
f
Safety valve and pressure limiting valve.
The safety valve is also a pressure limiting valve.
When the gun trigger is released, the valve opens and
the water recirculates through the pump inlet.
f
Safety catch (11): Prevents accidental
spraying of water.
INSTALLATION (Fig. B)
ASSEMBLY
Caution! All installation and assembly operations must
be performed with the appliance disconnected from the
mains power supply.
The assembly sequence is illustrated in (Fig. B).
Electrical connection
The electrical connection should be made by a qualified
electrician and should comply with regulations.
Caution! Check that the electrical supply voltage
and frequency (V/Hz) correspond to those on the
appliance data plate (Fig. B6). The appliance should
only be connected to a mains power supply equipped with
an adequate earth connection and a d erential security
breaker (30mA) to cut off the electricity supply in the
instance of a short circuit.
Use of extension cables: Use cables featuring “IPX5”
protection level. The cross-section of the extension cable
should be proportionate to its length; the longer it is, the
greater its cross-section should be.
Follow the instructions in Table I (Fig. F).
Water supply connection
Caution! Only clean or filtered water should be used for
intake. The delivery of the water intake tap should be equal
to that of pump capacity. Place the appliance as close to
the water supply system as possible.
Connection points:
Water outlet (OUTLET)
Water inlet with filter (INLET)
Connection to the mains water supply
The appliance can be connected directly to the mains
drinking water supply only if the supply hose is fitted with a
backflow preventer valve as per current regulations in force.
Make sure that the hose is at least Ø 13mm and that it is
reinforced.
ADJUSTMENT INFORMATION (Fig. C)
f
Adjusting the spray nozzle (for models with this
feature) Water flow is adjusted by regulating the
nozzle (12).
f
Adjusting the detergent (on models with this feature)
Detergent flow is adjusted using the regulator.
f
Adjusting the detergent pressure set the adjustable
nozzle (12) on “ ” to deliver detergent at the correct
pressure (on models with this feature).
f
Adjusting the pressure (on models with this feature)
The regulator (12) is used to adjust the working
pressure. The pressure is shown on the pressure
gauge (where fitted).
USE OF THE APPLIANCE (Fig. D)
CONTROLS
Operating in high pressure mode
f
Unwind the high pressure hose to the required length.
f
Hold the gun open for a few seconds.
f
Turn the master switch (D14) to (ON/I).
f
Set the nozzle (Fig. A1) in high pressure mode
(fully back (Fig.C, “ “position).
f
Press the trigger of the gun (Fig. D15) to obtain a jet
of water. Adjust the type of jet by turning the nozzle
(Fig. C12).