Black & Decker KR85, Оригинальное руководство пользователя

Страница: 5 / 12

5
f. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed.
Use of the power tool
for operations different from those intended could result
in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions for impact drills
◆
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
◆
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
◆
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
◆
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Variable speed control switch
4. Forward/reverse slider
5. Two-gear selector
6. Drilling mode selector
7. Spindle lock knob
8. Chuck
9. Depth stop
10. Side handle
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (fig. A)
◆
Turn the grip counterclockwise until you can slide the side
handle (10) onto the front of the tool as shown.
◆
Rotate the side handle into the desired position.
◆
Insert the depth stop (9) into the mounting hole as shown.
◆
Set the drilling depth as described below.
◆
Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit (fig. B & C)
Keyless chuck with spindle lock (fig. B)
◆
Open the chuck by turning the sleeve (11)
counterclockwise with one hand while holding the spindle
lock knob (7) with the other.
◆
Insert the bit shaft (12) into the chuck.
◆
Firmly tighten the chuck while holding the spindle lock knob.
Keyed chuck (fig. C)
◆
Open the chuck by turning the sleeve (13) counterclockwise.
◆
Insert the bit shaft (12) into the chuck.
◆
Insert the chuck key (14) into each hole (15) in the side of
the chuck and turn clockwise until tight.
Removing and refitting the chuck (fig. D & E)
◆
Open the chuck as far as possible.
◆
Remove the chuck retaining screw, located in the chuck,
by turning it clockwise using a screwdriver.
◆
Tighten an Allen key into the chuck and strike it with
a hammer as shown.
◆
Remove the Allen key.
◆
Remove the chuck by turning it counterclockwise.
◆
To refit the chuck, screw it onto the spindle and secure it
with the chuck retaining screw.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
◆
To select forward rotation, push the forward/reverse
switch (4) to the right.
◆
To select reverse rotation, push the forward/reverse
switch (4) to the left.
Warning! Never change the direction of rotation while the
motor is running.