Black & Decker JT2504BD Скачать руководство пользователя | Manualshive

Страница: 8 / 46

background image

8

GLOSSARY OF TERMS

ANTI-KICKBACK PAWLS – Prevents the
workpiece from being kicked upward or
back toward the front of the table saw by
the spinning blade.
ARBOR – The shaft on which the blade or
dado is mounted.
BEVEL CUT – An angle cut made through
the face of the workpiece.
BLADE BEVEL SCALE – Measures the
angle the blade is tilted when set for a
bevel cut.
BLADE ELEVATION AND TILTING
HANDWHEEL – Raises and lowers the
blade or tilts the blade to angle between
0° and 45° for bevel cuts.
BLADE GUARD – Clear plastic cover
that positions itself over the blade while
cutting.
COMPOUND CUT – A simultaneous
bevel and miter cut.
CROSSCUT – A cut made across the
width of the workpiece.
DADO – Special cutting blades that are
used to cut grooves in a workpiece.
FEATHERBOARD – When ripping a
workpiece on your table saw, this keeps

it firmly and safely against the rip fence. It

also helps prevent chatter, gouging, and
dangerous kickback.
FREEHAND – Performing a cut without
using a rip fence, miter gauge, hold down
or other proper device to prevent the
workpiece from twisting during the cutting
operation.
GUM – A sticky sap from wood products.
HEEL – Misalignment of the blade.
JAMB NUT – Nut used to lock another nut
in place on a threaded rod or bolt.

KERF – The amount of material removed
by the blade cut.
KICKBACK – Occurs when the saw blade
binds in the cut and violently thrusts the
workpiece back toward the operator.
MITER CUT – An angle cut made across
the width of the workpiece.
MITER GAUGE – A guide used for
crosscutting operations that slides in the
table top channels (grooves) located on
either side of the blade. It helps make
accurate straight or angle crosscuts.

CAUTION

!

In all cases, make certain

the receptacle is properly grounded. If

you are not sure, have a qualified

electrician check the receptacle.

Fig. 1

Fig. 2

Three-Pronged Plug

Grounding Prong

Properly Grounded
Three-Pronged
Receptacle

Grounding Lug

Make sure this
is connected
to a known
ground.

Two-Pronged
Receptacle

Adapter

«
...
6
7
8
9
10
...
»

Содержание JT2504BD















































Отзывы:

Нет отзывов

Похожие инструкции для JT2504BD

Бренд: MICRO-MARK Страницы: 6

WOODWORKER CTS800B

Бренд: Clarke Страницы: 15

Бренд: Parkside Страницы: 52

Бренд: King Canada Страницы: 4

Бренд: Battipav Страницы: 23

Бренд: Erbauer Страницы: 40

Бренд: Wesco Страницы: 32

Бренд: Milwaukee Страницы: 51

Бренд: Ozito Страницы: 2

EnergyBand-80LD2

Бренд: PEUGEOT Страницы: 24

Бренд: Baileigh Страницы: 60

Бренд: RedMax Страницы: 44

POWER PRUNER 99944200530

Бренд: Echo Страницы: 20

Бренд: Master Cut Страницы: 32

Бренд: Baumr-AG Страницы: 19

Бренд: WIDDER TOOLS Страницы: 5

Бренд: B+BTec Страницы: 36

Бренд: AGP Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды