Dual Range Gearing - Figure 6
The dual range feature of your drill allows you to shift gears for greater versatility. To select
position 1, turn tool off and permit to stop. Push button forward towards the chuck. Position 1
is for driving and removing screws and drilling in non-hammer mode. To select position 2,
turn tool off and permit to stop. Slide gear shifter back (away from chuck). Position 2 is for
drilling with hammer action.
N O T E :
Do not change gears when tool is running. If you are
having trouble changing gears, make sure that the dual range gear button is either
completely pushed forward or completely pushed back.
Keyless Chuck
To insert a drill bit or other accessory:
1. Grasp the rear half of the chuck with one hand and use your other hand to rotate the
front half in the counterclockwise direction, as viewed from the chuck end.
2. Insert the bit or other accessory fully into the chuck, and tighten securely by holding the
rear half of the chuck and rotating the front portion in the clockwise direction as viewed
from the chuck end.
WARNING:
Do not attempt to tighten drill bits (or any other accessory) by gripping the
front part of the chuck and turning the tool on. Damage to the chuck and personal injury may
occur when changing accessories.
S c rew Driving
For driving fasteners, the reversing button should be pushed to the left. Use reverse (button
pushed to the right) for removing fasteners. When moving from forward to reverse, or vice
versa, always release the trigger switch first.
D r i l l i n g
• Use sharp drill bits only.
• Support and secure work properly, as instructed in the Safety Instructions.
• Use appropriate and required safety equipment, as instructed in the Safety Instructions.
• Secure and maintain work area, as instructed in the Safety Instructions.
• Run the drill very slowly, using light pressure, until the hole is started enough to keep the
drill bit from slipping out of it.
• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but
not so much as to stall the motor or deflect the bit.
• Hold the drill firmly with two hands to control its twisting action.
• DO NOT CLICK THE TRIGGER OF A S TALLED DRILL OFF AND ON IN AN AT T E M P T TO
S TA RT I T. DAMAGE TO THE DRILL CAN RESULT.
• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last
part of the hole.
• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce
j a m m i n g .
•
Make sure switch turns drill on and off.
WA R N I N G :
It is important to support the work properly and to hold the drill firmly to
prevent loss of control which could cause personal injury. If you have any questions on how
to properly operate tool, call:
1 - 8 0 0 - 5 4 - H O W- TO (544-6986).
Drilling In Wo o d
Holes in wood can be made with the same twist drill bits used for metal or with spade bits.
These bits should be sharp and should be pulled out frequently when drilling to clear chips
from the flutes.
Drilling In Metal
Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which
should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil.
Drilling in Masonry
Select position 2 for drilling with hammer action. Use carbide tipped masonry bits. Refer to
Drilling section. Keep even force on the drill but not so much that you crack the brittle
material. A smooth, even flow of dust indicates the proper drilling rate.
M a i n t e n a n c e
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
I M P O R TA N T:
To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual) should be performed by authorized service
centers or other qualified service personnel, always using identical replacement parts.
The RBRC™ Seal
The RBRC™ (Rechargeable Battery Recycling Corporation)
Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to
recycle the battery (or battery pack) at the end of its useful life have already been
paid by Black & Decker. In some areas, it is illegal to place spent nickel-cadmium
batteries in the trash or municipal solid waste stream and the RBRC program provides an
environmentally conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established
programs in the United States and Canada to facilitate the collection of spent
nickel-cadmium batteries. Help protect our environment and conserve natural resources by
returning the spent nickel-cadmium battery to an authorized Black & Decker service center
or to your local retailer for recycling. You may also contact your local recycling center for
information on where to drop off the spent battery, or call
1 - 8 0 0 - 8 - B AT T E RY
.
A c c e s s o r i e s
Recommended accessories for use with your tool are available from your local dealer or
authorized service center. If you need assistance regarding accessories, please call:
1 - 8 0 0 - 5 4 - H O W- TO (544-6986).
WA R N I N G :
The use of any accessory not recommended for use with this tool could
be hazardous.
The following accessories should be used only in the sizes specified below:
BITS, META L DRILLING – Up to 1/2"(12.7mm); BITS, MASONRY DRILLING – Up to
1/2"(12.7mm); WOOD DRILLING – Up to 1-1/2"(38.1mm) Soft Wood, 1-1/4"(31.7mm) Hard
Wo o d .
Service Information
All Black & Decker Service Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you. To find
your local service location, refer to the yellow page directory under "Tools—Electric" or call:
1-800-544-6986 or visit www. b l a c k a n d d e c k e r. c o m
Full Tw o - Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of
two ways.
Safety Warnings and Instructions: Charging
1. This manual contains important safety and operating instructions.
2. Before using battery charger, read all instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product using battery.
3.
CAUTION:
To reduce the risk of injury, charge only Black & Decker Power Packs.
Other types of batteries may burst causing personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold by Black & Decker may result in a risk
of fire, electric shock, or injury to persons.
6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when
disconnecting charger.
7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise
subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary. Use of improper
extension cord could result in a risk of fire, electric shock or electrocution.
a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round jacketed
extension cords should be used, and we recommend that they be listed by
Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord must
be suitable for outdoor use. Any cord marked for outdoor use can also be used for
indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is suitable
for outdoor use.
b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety, and to prevent loss of power and overheating. The smaller the gauge number of
the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than
18 gauge. When using more than one extension to make up the total length, be sure
each extension contains at least the minimum wire size.
CHART FOR MINIMUM WIRE SIZE (AWG)OF EXTENSION CORDS
N A M E P L ATE RATING AMPS – 0 – 10.0
Total Extension Cord Length (ft) 2 5
5 0
7 5
1 0 0
125 150
Wire Gauge
1 8
1 8
1 6
1 6
14 14
9. Use only the supplied charger when charging your power pack. The use of any other
charger could damage the power pack or create a hazardous condition.
10. Use only one charger when charging.
11. Do not attempt to open the charger or the drill. There are no customer serviceable parts
inside. Return to any authorized Black & Decker service center.
12. DO NOT incinerate the drill or battery packs even if they are severely damaged or
completely worn out. The batteries can explode in a fire.
13. A small leakage of liquid from the battery cells may occur under extreme usage,
charging or temperature conditions. This does not indicate a failure. However, if the
outer seal is broken and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10
minutes and seek immediate medical attention.
MEDICAL NOTE:
The liquid is a
25-35% solution of potassium hydroxide.
Charging the Power Pack
THE BATTERIES IN YOUR POWER PACK ARE NOT F U L LY CHARGED AT T H E
FA C TO RY. BEFORE ATTEMPTING TO CHARGE THEM, T H O R O U G H LY READ A L L O F
THE SAFETY I N S T R U C T I O N S .
The charger is designed to use standard household 120 volt 60 Hz power.
1. Plug the charger into any standard 120 Volt 60 Hz electrical outlet.
NOTE: Do not
charge by means of an engine generator or DC power source. Use only 120V AC.
2. Slide the charger onto the power pack as shown in
Figure 1
and let the power pack
charge initially for
9 hours
. After the initial charge, under normal usage, your power
pack should be fully charged in
3 to 6 hours
.
3. Unplug charger, and remove the power pack.
Place the power pack in the tool and
be certain that it is inserted fully into the tool cavity until it “clicks” into place.
NOTE:
To remove the power pack from the drill, press down on the release button on
the back of the pack
(Figure 2)
and slide out.
Important Charging Notes
1. After normal usage, your power pack should be fully charged in 3 to 6 hours. If the
power pack is run-down completely, it may take up to 6 hours to become fully charged.
Your power pack was sent from the factory in an uncharged condition. Before attempt-
ing to use it, it must be charged for at least 9 hours.
2. DO NOT charge the power pack in an air temperature below +40°F(+4.5°C), or above
+105°F (+40.5°C). This is important and will prevent serious damage to the power pack.
Longest life and best performance can be obtained if power pack is charged when air
temperature is about 75°F (2 4 ° C ).
3. While charging, the charger may hum and become warm to touch. This is a normal con-
dition and does not indicate a problem.
4. If the power pack does not charge properly—(1) Check current at receptacle by plug-
ging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light
switch which turns power off when you turn out the lights. (3) Move charger and power
pack to a surrounding air temperature of 40°F (+4.5°C) to 105°F ( + 4 0 . 5 ° C ). (4) If the
receptacle and temperature are OK, and you do not get proper charging, take or send
the power pack and charger to your local Black & Decker service center. See Tools
Electric in yellow pages.
5. The power pack should be recharged when it fails to produce sufficient power on jobs
which were easily done previously. DO NOT CONTINUE using product with its power
pack in a depleted condition.
6. To prolong power pack life, avoid leaving the power pack on charge for extended periods
of time (over 30 days without use). Although overcharging is not a safety concern, it can
significantly reduce overall power pack life.
7. The power pack will reach optimum performance after being cycled 5 times during
normal usage. There is no need to run the batteries down completely before recharging.
Normal usage is the best method of discharging and recharging the power pack.
Maintenance Stage
The trickle charge feature of the charger allows the power pack to remain in the charger and
ready for use. With the charger connected to standard household current, the red charging
indicator light will glow constantly. The charger will keep the power pack fully charged. A
power pack will slowly lose its charge when kept out of the charger.
Safety Wa rnings and Instructions: Drills
1. As shown in
figure 3,
always hold drill firmly to control its twisting action. Make sure
that the side handle is securely attached and hand tightened to the orange housing sur-
face directly behind the torque adjust collar.
2. When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly.
WARNING:
Drill may stall (if overloaded or improperly used) causing a twist. A l w a y s
expect the stall. Grip the drill firmly to control the twisting action
(see Fig. 3)
and prevent loss
of control which could cause personal injury. If a stall does occur, release the trigger
immediately and determine the reason for the stall before re-starting.
Operating Instructions
Trigger Switch & Reversing Button - Figure 4
The drill is turned ON and OFF by pulling and releasing the trigger switch shown in
Figure 4
.
The farther the trigger is depressed, the higher the speed of the drill. A f o r w a r d / r e v e r s e
control button determines the direction of the tool and also serves as a lock off button. To
select forward rotation, release the trigger switch and depress the forward/reverse control
button. To select reverse, depress the forward/reverse control button the opposite direction.
The center position of the control button locks the tool in the off position. When changing the
position of the control button, be sure the trigger is released.
To rque Control - Figure 5
This tool is fitted with a collar to select the operating mode and to set the torque for
tightening screws. Large screws and hard workpiece materials require a higher torque
setting than small screws and soft workpiece materials.
•
For drilling in wood, metal and plastics, set the collar to the drilling position symbol .
•
For screwdriving, set the collar to the desired setting. If you do not yet know the
appropriate setting, proceed as follows:
•
Set the collar to the lowest torque setting.
•
Tighten the first screw.
•
If the clutch ratchets before the desired result is achieved, increase the collar setting and
continue tightening the screw. Repeat until you reach the correct setting. Use this setting
for the remaining screws.
TROUBLESHOOTING
P r o b l e m
Possible Cause
Possible Solution
• Unit will not start.
• Battery not installed properly.
• Check battery installation.
• Battery not charged.
• Check battery charging
r e q u i r e m e n t s .
• Battery will not charge.
• Battery not inserted into charger.
• Insert battery into charger
until red LED appears.
• Charger not plugged in.
• Plug charger into a working
outlet. Refer to “Important
Charging Notes” for more
d e t a i l s .
• Check current at receptacle
by plugging in a lamp or other
a p p l i a n c e .
• Check to see if receptacle is
connected to a light switch
which turns power off when
you turn out the lights.
• Surrounding air temperature
• Move charger and tool to a
too hot or too cold.
surrounding air temperature
of above 40 degree F(4 , 5°C)
or below 105 degree F
(+ 4 0 , 5°C ).
For assistance with your product, visit our website
www.blackanddecker.com
for the loca-
tion of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
