ENGLISH • 19
make exposed metal parts of the power tool “live“ and
could give the operator an electric shock.
f
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
f
Recommendations for the use of a residual
current device with a rated residual current of 30mA
or less.
Using an Extension Lead
Extension Cords shall be not lighter than:
f
If rubber insulated, ordinary tough rubber sheathed
flexible cord (code designation 60245 IEC 53)
f
If polyvinyl chloride insulated, ordinary polyvinyl
chloride sheathed flexible cord (code designation
60227 IEC 53).
Always use an approved extension lead suitable for the
power input of this tool. Before use, inspect the extension
lead for signs of damage, wear and ageing. Replace
the extension lead if damaged or defective. When
using an extension lead on a reel, always unwind the
lead completely. Use of an extension lead not suitable
for the power input of the tool or which is damaged or
defective may result in a risk of fire and electric shock. It
is recommended that the extension lead is a maximum of
25m in length. Do Not use multiple extension leads.
f
Before use check the supply and extension cord
for signs of damage or aging. If the cord becomes
damaged during use, disconnect the cord from
the supply immediately.
Note: Do not touch the cord before disconnecting
the supply. Do not use the line trimmer if the cord
is damaged or worn.
f
Keep extension cord away from cutting line.
f
Never allow children or people unfamiliar with these
instructions to use the line trimmer.
f
Avoid using the line trimmer, while people, especially
children or pets, are nearby.
f
Use the line trimmer only in daylight or good artificial light.
f
Never operate the line trimmer with damaged guards
or without guards in place.
f
Switch on the line trimmer only when the hands and
feet are away from the cutting head.
f
Never fit metal cutting blades.
f
Use only the manufacturer’s recommended
replacement parts and accessories.
f
Always disconnect the line trimmer from the mains
when leaving the line trimmer unattended.
f
Disconnect the line trimmer from the mains before
carrying out maintenance or cleaning work.
f
Inspect and maintain the line trimmer regularly.
Have the line trimmer repaired only by an authorized
repairer.
f
Take care against injury from the blade(s) fitted for
trimming the cutting line length. After extending new
cutting line, always return the line trimmer to its
normal operating position before switching on.
f
When not in use, store the line trimmer out of the
reach of children.
f
Face the cutting head away from yourself, other
people and animals while the power is connected to
the line trimmer (especially during operation).
f
Disconnect the power when changing spools or
clearing grass from under the guard.
f
Disconnect the power from the line trimmer before
making any adjustments.
f
Use both handles.
f
Keep ventilation openings clear of debris. Keep
handles dry, clean and free of oil and grease.
f
Never reach underneath the line trimmer (the cutting
line area) until it has completely stopped and the
power has been disconnected.
ASSEMBLY
Warning! Before assembly, make sure that the line
trimmer is switched off and unplugged.
Fitting the edging wheel (Fig. B and C)
Note: Take care when unwrapping both halves of the
edging wheel (8) not to discard the two assembly screws
(ST3x12mm) attached.
1. Align both halves of the edging wheel (8) onto the line
trimmer housing are align (13a and 13b) as shown
(Fig. B).
2. Secure the edging wheel (8) in place with the two
screws supplied (13a and 13b) using a Phillips head
screwdriver
(Fig. C).
3. When secured ensure that the edging wheel is free to
rotate on the housing.
Fitting the safety guard (Fig. D)
1. Slide the safety guard (7) in the recess under the
edging wheel (8) and align (14) with the screw holes
either side of the motor housing, secure from
underneath with the two screws (ST4.2x15mm)
supplied using a Phillips head screwdriver.
Note: The edging wheel (8) should rotate on the trimmer
housing and not come into contact with the safety guard
(7) when both parts are fitted correctly.
Warning! Never use the line trimmer unless the safety
guard is properly fitted.
Fitting the auxiliary handle (Fig. E and F)
1. Rotate the bracket to the foreside of the main handle
(1) (Fig. E).
