4
ENGLISH
X
Before use, check the power supply cord for signs of
damage, ageing and wear.
X
Do not use the appliance if the power supply cord or
mains plug is damaged or defective (where applicable).
Labels on tools
The following pictograms are shown on the tool:
Features
1. Area light
2. Pressure gauge
3. Storage location for air hose and 12 Volt adaptor
4. Air hose with universal valve adaptor
5. On/off switch
6. 12 Volt adaptor
7. Area light on/off switch
Use
Air hose and cord storage (fig. A)
Wrap the dc cord around the base of the unit and then put
the air hose (4) and the 12 Volt adaptor (6) into the storage
location (3).
Fitting the accessories (fig. B and C)
Your inflator is supplied with the standard tapered nozzles
and the needle inflator nozzle, these are located on the base
of the unit (fig. C).
X
To use the universal valve adaptor, make sure that the
lever is in the up position.
X
Place the valve adapter over the stem of the inflation
needle or tapered nozzle (fig. B).
X
Press the lever on the valve adapter down to lock it in
place.
X
Place the inflation needle or tapered nozzle into the item
to be inflated.
Note:
Always make sure that the lever is in the up position
when not in use.
Operate your Inflator only with the universal valve adaptor or
with the included nozzles.
Note:
Make sure that the universal valve adaptor is firmly
locked in place before turning the Inflator on.
Many inflatables have an internal flap that prevents air loss
during inflation. Unless this flap is displaced by the nozzle
the inflatable will not inflate. Push the nozzle firmly into the
valve to make sure that you push this flap out of the way.
Store the inflation needle inside one of the tapered nozzles
and snap the tapered nozzles into the storage slots located
on the bottom of the Inflator (fig. C).
Warning!
Excessive air pressure may cause a hazardous
risk of bursting or personal injury. Check the manufacturer’s
maximum pressure rating for the items being inflated.
Note:
If the pressure rating for the item being inflated is
above 100 psi, note that the maximum run time is 10
minutes, leave to rest for 20 minutes before re-use.
Operating the inflator
Warning!
Do not operate the inflator when the car engine is
running.
Note:
Make sure that your 12 Volt accessory socket is live.
On some vehicles the accessory socket may only become
live when the ignition key is in the accessory position.
To power the display
X
Always fully extend the 12 Vdc cord before each use.
X
Connect the 12 Volt adaptor (6) into the vehicle’s
12 Volt accessory socket.
X
To enable the inflator to operate you must set the
required units (psi, bar or kPa) and a pressure valve.
Setting the required pressure (fig. D)
Warning!
Do not leave the inflator running unattended. It
could burst tyres or other items.
Note:
You must set the automatic shut-off feature before the
unit will operate.
X
To switch between the different units (kPa, psi or bar),
press buttons 8 & 9 at the same time until the required
units are displayed.
X
Press and hold button 8 or 9 for 3 seconds until the
display flashes.
X
While the display is flashing press the - or + buttons
(8 & 9) until the required pressure is displayed.
X
After 3 seconds the display will flash and return to a
reading of "0.0". This is normal.
X
Connect the universal valve adaptor and accessories, if
required, to the item to be inflated, making sure that the
lever of the valve adaptor is in the down position to lock
it in place.
X
To turn the inflator on, press the on/off switch (5) to the
I
position.
Warning!
To reduce the risk of injury, the user
must read the instruction manual.
Do not expose the appliance to rain or high
humidity
Before performing maintenance or cleaning on
the appliance, unplug the supply cord.
Do not leave the inflator unattended.
Содержание ASI200
Страница 2: ...2 A B C E D BAR 8 13 11 12 10 3 9 2 4 ...
