BK Precision XLN15010 Скачать руководство пользователя

Страница: 33 / 114

2.3

Rear Panel Overview

(16)

LAN (Ethernet) Interface:

RJ-45 LAN connector for remote communication.

(17)

GPIB Interface:

GPIB connector for remote communication.

(18)

Main Output (+ + - -):

The main output of the power supply.

(19)

Earth connection:

Used for earth ground connection.

(20)

USB Interface:

USB interface for remote communication.

(21)

RS485 Interface:

While operating in parallel connection or multi unit connection

(CHAIN) mode, the RS485 interface can be used for communication and
synchronization between master and slave.

(22)

Analog Interface:

Remote analog control interface allows for programming and monitoring
the power supply’s output with external analog controls.

(23)

RMT/LCL Sense:

When Remote sense is selected, the wire connection can be set up as

follows: positive sense (+S) and positive lead (+) of the DC output are
connected to the positive end (+) of the device, whereas negative sense

Содержание XLN15010



















































































































Результаты поиска

Содержание XLN15010

Отзывы:

Похожие инструкции для XLN15010

Бренды по названию

Популярные бренды

BK Precision XLN15010, Руководство пользователя

Результаты поиска

Содержание XLN15010

Отзывы:

Похожие инструкции для XLN15010

Бренды по названию

Популярные бренды