background image

11

Carpet Cleaning

1.

2.

3.

4.

5.

 ATTENTION 

BERBER CARPET 

OWNERS:

Some Berber Carpets have a 
tendency to fuzz with wear. 
Repeated strokes in the 
same area with an ordinary 
vacuum or deep cleaner may 
aggravate this condition. 
Please see Stain Removal 
instructions on page 12.

Plug into a proper outlet and turn the Power Switch 
ON. Wait two minutes for the heater to warm up before 
beginning to clean.

While pressing the trigger, make one slow forward wet 
pass and another one back. Let the SmartTemp heated 
formula and DirtLifter Powerbrush do the work for you. 

Caution: Do not overwet.

Note: Take care not to run over loose objects 

or edges of area rugs. Stalling brush may 
result in premature belt failure.

Release the trigger and make one slow forward and back 
pass over the same area to remove any residual dirty water.

Repeat cleaning passes until solution being pulled up 
appears clean.

Continue passes without pressing the trigger until you 
can’t see any more water being pulled up. 

Note: Both the SmartMix Bottle and the clean 

water Tank must have liquid in them in 
order for the machine to spray. If one is 
empty, the machine will temporarily lose 
its prime and will not spray cleaning 
solution or water. 

After cleaning, you may want to turn the SmartMix Dial 
to the 

Water Rinse/Carpet

 

Protector

 setting to give 

your carpeting a final rinse. This will ensure thorough 
removal of embedded dirt loosened by the BISSELL 
Advanced Deep Cleaning Formula. BISSELL Advanced 
Deep Cleaning Formulas contain an anti-resoiling agent 
that helps your carpets repel dirt and keeps them looking 
good longer. 

When the cleaning job is complete refer to the 

Maintenance

 section for machine cleanup and storage 

instructions on pages 17-19

.

Note: You may notice hair and debris deposits 

on the carpet that were loosened by the 
brushing action (especially with newer 
carpets that have never been deep cleaned 
before). This debris should be picked up 
and thrown away. Debris that deposits in 
the Brush Belt should be cleaned between 
uses to keep the Belts running free.

6.

7.

ug310-5815_7920E_604.indd   11

ug310-5815_7920E_604.indd   11

3/29/06   3:39:46 PM

3/29/06   3:39:46 PM

Содержание ProHeat Pro-Tech 7920 SERIES

























Отзывы: