manualshive.com logo in svg

BIRO 1433FH, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
BIRO 1433FH Скачать руководство пользователя страница 8

10. Placing blade on cutter: Unpack upper wheel assembly and hang on the hinge bracket in the head structure. Lift

the nylon filler in the stationary bar. Hang the blade on the upper wheel and hold with right hand. With the left
hand force the back of the blade between the front blade scrapers, located below the stationary bar. Lower the
nylon filler. Be sure the blade is in the upper saw guide. The blade has dropped over the lower wheel. Switch
hands holding the blade on the upper wheel. With the right hand, force the blade between the rear blade
scrapers. The blade is now ready to be tightened.

11. Turn the blade tensioning handle clockwise until the tension mark is even with the bottom of the upper wheel

hinge plate as shown. Carefully turn saw wheels by hand and watch for proper tracking of blade on the wheels.

12. The stationary platter (Part No.

A14163

) is placed on top of the base structure and held in place by two push-pull

hold down rods (Part No.

14212W

), located at the rear of the base.

13. The sliding meat carriage assembly (Part No.

A16155EZ

) is installed by turning the movable stop assembly (Part

No.

A16200

) clockwise. After the carriage assembly is in the channel for operation, turn the movable stop

counterclockwise to lock.

14. Make sure saw guide bar with saw guard is in its lowest position. Close head and base doors.

15. Push the start button. Check for proper phasing of the motor and proper tracking of the saw blade in the saw

guides. Back of the blade should be centered in the lower saw guide (Part No. 119A) in the stationary bar. Blade
should be moving down through the guide. Push the stop button to stop the machine.

16. Check placement of all warning labels, wall chart and Manual. Machine is ready for trained operators to process

product. Post SAFETY TIPS wall chart within easy view of operator. Keep Manual available to operator.

17. Contact your local Distributor or BIRO directly if you have any questions or problems with the installation or

operation of this machine.

6

SHARP SAW BLADE. HANDLE WITH EXTREME CAUTION.

KEEP HANDS CLEAR OF SHARP MOVING BAND TYPE SAW
BLADE

27

Содержание 1433FH





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды