BIRD SiteHawk SK-200-TC Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 65

background image

Bird SiteHawk Operation Manual

35

Figure

25

Delete User File dialog box

Site Name

Press to toggle ON or OFF, when set to ON the site name will be included on all
screen shots.

After Site Name is set to ON, an Edit SiteName dialog box will be displayed each
time a screen shot is taken. See

The site name must be entered the first time a screen shot is saved.

Note:

The default setting for the Site Name option is OFF. If the

SiteHawk application is exited or SiteHawk is powered off the site name is reset
to NULL and the Site Name option is reset to OFF.

Figure

26

Site Name Dialog Box

The site name will appear at the bottom of the sweep display screen shot. See

If no site name was entered NULL will appear in place of the site name.

Figure

27

Site Name Screenshot

«
...
42
43
44
45
46
...
»

Содержание SiteHawk SK-200-TC


































































Отзывы:

Нет отзывов

Похожие инструкции для SiteHawk SK-200-TC

Бренд: Kawai Страницы: 70

Бренд: Medeli Страницы: 14

SXNP10 - DIGITAL PIANO

Бренд: Panasonic Страницы: 63

Бренд: E-line Страницы: 164

Бренд: Kane Страницы: 19

Бренд: Accurate Logic Страницы: 50

Acuvim-L Series

Бренд: AccuEnergy Страницы: 188

Бренд: VAMP Страницы: 78

Бренд: Vanguard Instruments Страницы: 24

Бренд: Oakton Страницы: 4

Бренд: Nady Audio Страницы: 2

Бренд: VeEX Страницы: 842

Бренд: Garmin Страницы: 22

Бренд: Keysight Страницы: 92

LaserHybrid SB 360i

Бренд: Fronius Страницы: 104

Ocean Optics HR2000 Series

Бренд: Halma Страницы: 42

Бренд: Roland Страницы: 2

Бренд: Lambda Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды