Bird Electronic Thruline 4020 Series Скачать руководство пользователя

Страница: 47 / 59

Maintenance

Cord Reel (Cal Cart only)

1. Disconnect the cord reel from the terminal strip.
2. Unscrew the AC connector.
3. Unscrew and remove the cord reel.
4. Screw the replacement cord reel into place.
5. Thread the AC connector through the grommet, and connect the wires on

the other end to the terminal strip (See Figure 18).

Replacing Fuses

1. Gently pry the fuse drawer out of the ac module. The fuse holder does not

detach from the AC module.

2. Install the replacement fuses then close and secure the fuse holder. Fuse 1

is a spare fuse and fuse 2 is the active fuse.

Figure 18 AC Line Fuse

WARNING

To avoid personal injury, disconnect the power cord from the ac line before

performing any maintenance, including fuse replacement.

CAUTION

Failure to install the properly rated fuse may result in equipment damage or

nuisance failures.

AC Line Voltage

Fuse Rating

115 Vac

T630 mA, 5x20 mm Time Lag Fuse

230 Vac

T315 mA, 5x20 mm Time Lag Fuse

Fuse 1

Fuse 2

Fuse

Drawer

AC Module

Содержание Thruline 4020 Series




























































Результаты поиска

Содержание Thruline 4020 Series

Отзывы:

Похожие инструкции для Thruline 4020 Series

Бренды по названию

Популярные бренды

Bird Electronic Thruline 4020 Series, Инструкция

Результаты поиска

Содержание Thruline 4020 Series

Отзывы:

Похожие инструкции для Thruline 4020 Series

Бренды по названию

Популярные бренды