Bird Electronic Thruline 4020 Series Скачать руководство пользователя

Страница: 2 / 59

iii

Safety Precautions

The following are general safety precautions that are not necessarily related to

any specific part or procedure, and do not necessarily appear elsewhere in this

publication. These precautions must be thoroughly understood and apply to all

phases of operation and maintenance.

Safety Symbols

The caution symbol appears on the equipment indicating there is

important information in the instruction manual regarding that

particular area.

Note:

Calls attention to supplemental information.

WARNING

Keep Away From Live Circuits

Operating Personnel must at all times observe general safety precautions.

Do not replace components or make adjustments to the inside of the test

equipment with the high voltage supply turned on. To avoid casualties,

always remove power.

WARNING

Shock Hazard

Do not attempt to remove the RF transmission line while RF power is present.

WARNING

Do Not Service Or Adjust Alone

Under no circumstances should any person reach into an enclosure for the

purpose of service or adjustment of equipment except in the presence of

someone who is capable of rendering aid.

WARNING

Safety Earth Ground

An uniterruptible earth safety ground must be supplied from the main

power source to test instruments. Grounding one conductor of a two

conductor power cable is not sufficient protection. Serious injury or death

can occur if this grounding is not properly supplied.

WARNING

Chemical Hazard

Dry cleaning solvents for cleaning parts may be potentially dangerous. Avoid

inhalation of fumes or prolonged contact with skin.

WARNING

Resuscitation

Personnel working with or near high voltages should be familiar with

modern methods of resuscitation.

WARNING

Remove Power

Observe general safety precautions. Do not open the instrument with the power on.

WARNING

Warning notes call attention to a procedure which, if not correctly

performed, could result in personal injury.

CAUTION

Caution notes call attention to a procedure which, if not correctly performed,

could result in damage to the instrument.

Содержание Thruline 4020 Series




























































Результаты поиска

Содержание Thruline 4020 Series

Отзывы:

Похожие инструкции для Thruline 4020 Series

Бренды по названию

Популярные бренды

Bird Electronic Thruline 4020 Series, Инструкция

Результаты поиска

Содержание Thruline 4020 Series

Отзывы:

Похожие инструкции для Thruline 4020 Series

Бренды по названию

Популярные бренды