Bird Electronic Thruline 4020 Series Скачать руководство пользователя

Страница: 43 / 59

Chapter 6

Maintenance

This chapter describes routine maintenance, along with troubleshooting

instructions for the power meter and power sensor. Disassembly instructions

for the Bird Cal Cart are also provided. For service beyond this level, return

the unit to a qualified service center.

The Bird 4421 Power Meter requires only simple, routine maintenance.

Wipe off dust and dirt regularly.

Check the connectors and cables for damage.

Clean the connector contacts with alcohol or dry cleaning solvent.

Cleaning

Clean the Bird 4421 Power Meter and its display with a soft cloth dampened

with mild detergent and water only. Clean sensors with a dry cleaning solvent

that leaves no residue.

Troubleshooting

Since the power meter and power sensor can only work together, the first step

is to determine which is malfunctioning. Connect the power sensor to the

meter and perform the functional test on page 37. If the power meter is mal-

functioning, refer to the troubleshooting table below. If the power sensor is

malfunctioning, return it for service.

This manual cannot list all malfunctions that may occur, or corrective actions.

If a malfunction is not listed or is not corrected by the listed corrective actions,

contact a qualified service center.

Note:

For power sensors in Cal Carts, following the test procedure

will check the sensor not covered by the safety cover. To test the other

sensor slide the safety cover over, then proceed as normal.

WARNING

To avoid personal injury, disconnect the power cord from the AC line before

performing any maintenance, including fuse replacement or changing the

line voltage setting.

WARNING

Never attempt to connect or disconnect RF equipment from the transmission

line while RF power is being applied.

Leaking RF energy is a potential health hazard.

WARNING

The Bird 4421 contains no user-serviceable parts. Do not remove its cover.

CAUTION

Do not use harsh or abrasive detergents for cleaning.

CAUTION

Due to the complexity of the Bird Power Sensor, field repairs beyond general

maintenance should not be attempted.

Removal or disturbance of the power sensor cover can result in cancellation

of lifetime warranty.

Содержание Thruline 4020 Series




























































Результаты поиска

Содержание Thruline 4020 Series

Отзывы:

Похожие инструкции для Thruline 4020 Series

Бренды по названию

Популярные бренды

Bird Electronic Thruline 4020 Series, Инструкция

Результаты поиска

Содержание Thruline 4020 Series

Отзывы:

Похожие инструкции для Thruline 4020 Series

Бренды по названию

Популярные бренды