9
or low levels of airborne particles to red which shows poor
air quality conditions or high levels of airborne particulate.
•
The air quality sensor operates continuously when the
Galileo
®
Wireless Air Quality Center is plugged into a 120V
AC outlet, even when the air cleaner is turned off.
SENSOR CONTROL MODE
When the Galileo
®
Wireless Air Quality Center is in the “Sensor
Control” mode, it will automatically adjust the fan setting to the
optimum speed based on the air quality conditions and particle
levels in the air. As the particle concentration in the air rises, so
does the speed. In sensor control mode, the unit will always run
at a minimum of SLEEP speed even if the particle levels are low
to maintain ideal conditions.
1. To turn the air cleaner onto “Sensor Control” mode, you
must use the Galileo
®
Wireless Air Quality Center.
2. Turn the air cleaner on using the Operating Instructions.
Select the desired operating speed by scrolling through
the settings using the “MODE” button. You can select from
“HIGH” , “MEDIUM”, “LOW”, “SLEEP” or “Sensor Control.”
3. Once in “Sensor Control” mode, the air cleaner speed will
fluctuate depending on airborne particulate concentration.
NOTE:
The Sensor Control mode cannot be controlled from
the air cleaner control panel. It can only be controlled using
the Galileo
®
Wireless Air Quality Center.
AIR QUALITY SENSOR CLEANING INSTRUCTIONS
It is recommended that you clean the air quality sensor monthly
to maintain accurate monitoring or particulate levels.
1. Turn off and unplug unit before cleaning.
2. The air quality sensor is located on the
back side of the Galileo
®
Wireless Air
Quality Center.
3. Open the sensor door (see Figure 3)
4. Use a dry cotton swab to gently clean
the sensor lens. Do not use any water
or cleaning agents.
5. Securely close the sensor door. If it is not
closed, the sensor may not operate properly.
OSCILLATION
The air cleaner is equipped with oscillation. To start and stop
oscillation of the air cleaner, push the button identified as
Oscillation (
) on the air cleaner control panel.
CLEANING/MAINTENANCE INSTRUCTIONS
Turn off and unplug the unit before cleaning.
1. The outside of the air cleaner can be cleaned with a soft,
damp cloth.
2. The rear air inlet grill can be removed and washed in warm soapy
Figure 3
operating controls directly on the air cleaner, the yellow LED light
will turn off. To resume primary control from the Galileo
®
Wireless
Air Quality Center, press the “ON/OFF” or “MODE” button. The
yellow LED light on the air cleaner will again illuminate.
OPERATING INSTRUCTIONS
1. The air cleaner can be operated from either the control
panel directly on the air cleaner or the Galileo
®
Wireless Air
Quality Center.
2. To turn the air cleaner on, press the “ON/OFF” button on the
Galileo
®
Wireless Air Quality Center OR press the power button
( ) on the air cleaner.
3. Select the desired operating speed. You can select from HIGH
(
), MEDIUM (
), LOW (
) or SLEEP (
) by pressing
the “MODE” button on either the air cleaner control panel or
the Galileo
®
Wireless Air Quality Center.
4. The light on the control panel will illuminate letting you know
the power is on and at what speed the air cleaner is operating.
5. To release negative ions into the filtered air, press the
ionizer button ( ) to ON and the light will illuminate.
6. For optimum air filtration, it is recommended to operate
the air cleaner continuously. Its rugged motor has been
designed to provide many years of continuous use.
For continuous use, it is recommended to operate the air
cleaner on the LOW or MEDIUM setting. For quieter operation
or use in a bedroom, select the LOW or ultra-low SLEEP
setting. When high levels of air pollution are present, select
the HIGH setting to quickly circulate and filter the room air.
NIGHTLIGHT
Your Galileo
®
Wireless Air Quality Center has a built in nightlight
which automatically turns on as your room gets dark. To turn off
this nightlight, press the “+” and “-” buttons at the same time.
To turn this function back on simply press both buttons again.
Note:
When any button is pressed the backlight will come on
for a few seconds.Once no buttons are pressed again for 5
seconds, the light will go off.
AIR QUALITY SENSOR
Your Bionaire
®
Air Cleaner comes with an Air Quality Sensor
which uses an advanced infrared optical system to constantly
detect tiny particles in the air around the Galileo
®
Wireless Air
Quality Center such as pollen and dust. It also displays the air
quality even when the air cleaner is turned off, using a series of
colored lights. Radio frequency technology sends continuous
signals between the air cleaner and the Galileo
®
Wireless Air
Quality Center sensor and adjusts air cleaner to improve air
quality wherever it is placed.
•
The air quality sensor uses a series of lights to indicate air
quality conditions and particle levels. The lights range in
color from green, which indicates good air quality conditions
8
BAP2000/200105EM1 P.qxd 5/20/05 16:04 Page 15
