5
94VT (.052”) 1.3mm Carbide Tip
94P, 97P
54-4383 VT
901VT (.066”) 1.6 mm Carbide Tip
54-4384 VT
903 (.079”) 2.0 mm
54-4382/54-4381
905 (.089”) 2.3 mm
54-4382/54-4381
905VT (.088”) 2.3 mm Carbide Tip
905P
54-4385 VT
906 (.100”) 2.5 mm
54-4382/54-4381
909 (.111”) 2.8 mm
54-4382/54-4381
909VT (.112”) 2.8 mm Carbide Tip
54-4386
STANDARD FLUID NOZZLES
FLUID NOZZLES
90F (.030") 0.8 mm
94P
54-4387
91F (.040") 1.0 mm
97P
54-4388
92F (.046") 1.2 mm
91P, 92P*
54-4389
94F (.055") 1.4 mm
95AP**
●
54-4390
97F (.070") 1.7 mm
97AP**
●
54-4391
ULTRA LIGHT / Reduced Flow
89 (.020” Dia.) 0.5 mm
VERY LIGHT / Reduced Flow
90 (.030” Dia.) 0.8 mm
90P***
LIGHT: less than 15 to 20 seconds in a Zahn 2 Cup,
91 (.040” Dia.) 1.0 mm
95P, 97P,
e.g., stains, varnishes, thin lacquers, automotive refinishing fluids.
92 (.046” Dia.) 1.2 mm
92P*
SEE NOTE
MEDIUM: 20 to 60 seconds in a ZAHN 2 Cup,
94 (.055” Dia.) 1.4 mm
95AP, 97AP**
e.g., general industrial coatings.
93P, 94P
HEAVY: greater than 60 seconds in a Zahn 2 Cup.
97 (.070” Dia.) 1.7 mm
FLUID
FLUID NOZZLE NO.
APPLICABLE
AIR NOZZLE
FLUID
NEEDLE
NOTE:
Use stainless steel fluid needle (54-4382) for all above nozzles. Optional nylon-tipped stainless steel fluid needle (54-4381) is also available.
Binks needles AB and ABSS (54-3941 & 54-3940) may be used, but require readjustment of the needle cap and locknut position.
SPECIAL PURPOSE NOZZLES
TYPICAL APPLICATION
FLUID NOZZLE NO.
APPLICABLE
AIR NOZZLE
COMPATIBLE
FLUID
NEEDLE
VERY HEAVY FLUIDS:
Block Fillers, Texture Coatings, Fire
Retardants, Road Marking Paint,
Bitumastics, Adhesives, Celluar
Plastisols, Underbody & Vitreous
Coatings, Special Applications
FEATHERING
For applications requiring more
gradual fluid valve opening for
metering control of fluid flow
with trigger
SIPHON FEED-FINE FINISH
Light to medium fluids
Auto body spot repairs
Medium to heavy fluids
Auto body overall finishing
94s (.055") 1.4 mm
95AS
●
54-4390
97s (.070") 1.7 mm
54-4391
GS FLUID NOZZLES
LIGHT/MEDIUM: less than15 to 20 seconds in a Zahn 2 Cup,
92GS (.046” Dia.) 1.2 mm
SEE NOTE
e.g., stains, varnishes,thin lacquers, automotive refinishing materials.
93GS (.052” Dia.) 1.3 mm
94GS (.055” Dia.) 1.4 mm
MEDIUM: 20 to 60 seconds in a ZAHN 2 Cup,
95GS (.059” Dia.) 1.5 mm
96G
■
54-4547
e.g., general industrial coatings.
96GS (.063” Dia.) 1.6 mm
97GS (.070” Dia.) 1.7 mm
FLUID
FLUID NOZZLE NO.
APPLICABLE
AIR NOZZLE
FLUID
NEEDLE
NOTE:
Optimum setup for clear coat spray is 92GS Fluid Nozzle x 96G Air Nozzle Assembly.
* 92P Low Volume Nozzle for general industrial and
automotive fine finish.
** 95AP High Solids Nozzle for hard to atomize
coatings and higher flow rates. 97AP same as
95AP, but for wider fan if needed.
*** 90P Low Volume Nozzle, 1 1/2 H.P. Compressor or
bigger – (6 C.F.M) required.
●
95AP, 95AS and 97AP Air Nozzles do not require
separate Retainer Ring.
■
Improves atomization, breaks-up high solid material
easier, provides better finish at lower pressures and
reduces orange-peel dramatically.
54-4547 needle must be used in conjunction
with the GS fluid nozzle and 96G air nozzle.
96G Air Nozzle
92GS Fluid Nozzle
(.046") 1.2 mm
54-4547 CSS Needle
(Needs to be adjusted to fit your gun.
See adjustment guide at right.)
NEEDLE ADJUSTMENT LENGTH
(See adjustment guide at right.)
Needle
Adjustment Guide
Model
Length
MACH 1
5.8 in.
MACH 1SL
5.7 in.
M1-Gravity
5.5 in.
OPTIONAL GS FLUID
NOZZLE SIZES
Diameter
Nozzle
Inches
mm
92GS
.046
1.2
93GS
.051
1.3
94GS
.055
1.4
96GS
.063
1.6
Example:
93GS Fluid Nozzle,
96G Air Nozzle &
54-4547 Needle.
