background image

       Part No. 350245                                                                                                                                                            Form No. F011003A

Page 12 of 12

TROUBLESHOOTING

Before Requesting Service Review These Suggestions

Engine stalls or labors when raking.

Raise blades so that they just touch the ground on a
level surface.

Solution

Possible Cause

Problem

Blades set too deep into ground

20

Engine Service and Warranty

Contact your nearest engine manufacturer's

authorized servicing dealer. (See page 7)

22.1

22

BILLY GOAT INDUSTRIES INC.

1803 S.W.  JEFFERSON / LEE'S SUMMIT, MO 64082-2312  / USA
PHONE: 816-524-9666 FAX: 816-524-6983

www.billygoat.com

WARRANTY PROCEDURE

Purchased
from

Purchase
Date

21

Serial Plate

Record your machine model, serial number and
date-of-purchase and where purchased

R

min

-1

1803 S. Jefferson
Lee's Summit,
MO   64062  / USA
Tel (816) 524-9666
Fax (816) 524-6983

Model

Serial No.

Unit(Weight)

Engine Power

lbs.

kg

kW

rpm

Abnormal vibration.

Engine will not start.

Engine is locked, will not
pull over.

Debris locked against reel, or drive pulleys.  Engine
problem.

Check stop switches, throttle, choke position and
gasoline. Connect spark plug wire. Clean or replace
air cleaner. Contact a qualified service person.

Stop work immediately.  Replace any damaged or
missing blades.  Tighten all loose bolts and nuts.

Damaged or missing blades.  Loose handle bolts.
Loose engine bolts

Stop switch off (Honda only).  Throttle in off position.
Engine not in full choke position.  Out of gasoline.  Bad
or old gasoline.  Spark Plug wire disconnected.  Dirty air
cleaner. Engine oil level too low (Honda only).

Pull spark plug wire and remove debris.  Contact an
engine servicing dealer for engine problems.

MODEL NO.

GENERAL  ENGINE  SPECIFICATIONS

HORSEPOWER

ENGINE

BRIGGS &
STRATTON

HONDA

5.0

5.5

1104020191E1

GC160AQHA

GOVERNED RPM

3700

3600

ENGINE

When servicing engine refer to specific manufacturers engine
owner's manual.  All engine warranty is covered by the specific
engine manufacturer.  If your engine requires warranty or other
repair work contact your local servicing engine dealer.  When
contacting a dealer for service it is a good idea to have your engine
model number available for reference(See table page above).  If
you can not locate a servicing dealer in your area you can contact
the manufacturers national service organization.

To reach:

          

Briggs & Stratton:

 800-233-3723

          

American Honda:

  800-426-7701

           

Subaru America:

 800-277-6246

Never store engine indoors or in enclosed poorly ventilated

areas with fuel in tank, where fuel fumes may reach an open flame,
spark  or pilot light, as on a furnace, water heater, clothes dryer or
other gas appliance.

If engine is to be unused for 30 days or more, prepare as follows:

Remove all gasoline from carburetor and fuel tank to prevent

gum deposits from forming on these parts and causing possible
malfunction of engine. Drain fuel outdoors, into an approved
container, away from open flame.  Be sure engine is cool.  Do not
smoke. Run engine until fuel tank is empty and engine runs out of
gasoline.

NOTE:  

Fuel stabilizer (such as Sta-Bil) is an acceptable alternative in minimizing

the formation of fuel gum deposits during storage.  Add stabilizer to gasoline in
fuel tank or storage container.  Always follow mix ratio found on stabilizer
container.  Run engine at least 10 min. after adding stabilizer to allow it to reach

the carburetor.

UNIT STORAGE

R

Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:

The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.

The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.

The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.

The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.

The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.

Note:

   To process a Warranty Claim, it is necessary to quote the Model

             & Serial number who are printed on the Billy Goat Serial Plate.

99  dB

HONDA

5.5

GX160K1QX

3600

SUBARU

4.5

EX130D50030

3600

All manuals and user guides at all-guides.com

Содержание CR450S













Отзывы: