background image

 

We suggest that you read through the manual before starting the 

assembly.  If you have any questions or concerns please don’t 

hesitate to e-mail us at [email protected]

 

 

 

Thank you  

 

Bill Hempel 

 

   

 

 

Billhempel.com assumes no liability for any damage resulting 

from the user assembled product. By the act of using the assembled 

product, the user accepts all resulting liability.  The purchaser or 

designated person flying this aircraft accepts all liability associated 

with the use of this product. This product is sold as is and the 

purchaser accepts any and all responsibility for structural or 

mechanical failures.  Because of the stresses that are associated 

with aerobatic flight there is no warranty provided and 

bill.hempel.com cannot be held liable.  

 

 

 

WARNING: 

 

Radio Control Model aircraft are not toys.  If improperly used, it can 

cause serious injury or death.  Fly only in open areas, and at AMA 

(

Academy of Model Aeronautics

) approved flying sites.  The AMA 

Safety Code must be followed.  Follow all instructions included with 

your plane, radio, and engine. The purchaser accepts all liabilities. 

 

 

 

 

Содержание 42% Extra 260
































Отзывы: