7
BEFORE OPERATION
DURING OPERATION
Read and observe the following general safety
precautions before operating the ESP 19.
ALWAYS survey the usage area for potential
hazards such as untampered earth fills, unlevel
surfaces, overhead obstructions, and electrically
charged conductors or wires. Be aware of any
potential hazards and always consider what could
happen. Watch for moving vehicles in the operating
area.
ALWAYS read, understand, and follow the
procedures in this manual before attempting to
operate equipment.
ALWAYS inspect the equipment for damaged or
worn parts. Check for cracked welds, hydraulic
leaks, damaged wiring, loose wire connectors,
damaged casters, and damaged pothole guards.
Also check for any improper operation. NEVER
operate equipment if damaged in any way.
Improperly operating equipment must be repaired
before using.
ALWAYS wear proper clothing for the job. Wear
protective equipment as required by federal, state,
or local regulations.
ALWAYS locate, read, and follow all directions and
warnings displayed on the equipment.
ALWAYS inspect the equipment for “DO NOT USE”
tags installed by maintenance personnel. NEVER
use tagged equipment until repairs are made and all
tags are removed by authorized maintenance
personnel.
ALWAYS make sure the platform is free of mud,
grease, or other foreign material. This will reduce the
possibility of slipping.
NEVER allow improperly trained personnel to
operate this equipment. Only trained and authorized
personnel shall be allowed to operate this
equipment.
NEVER operate this equipment if you are under the
influence of alcohol or drugs or if you feel ill, dizzy,
or unsteady in any way. Operators must be
physically fit, thoroughly trained, and not easily
excitable.
NEVER modify, alter, or change the equipment in
any way that would affect its original design or
operation in any way.
NEVER operate this equipment in ways for which it
is not intended.
Ensure the following general safety precautions are
followed while operating the ESP 19:
DANGER
This machine is NOT insulated for use near
electrical power lines and DOES NOT provide
protection from contact with or close proximity
to any electrically charged conductor. Operator
must maintain safe clearances at all times (3.05
meters minimum) and must always allow for
platform movement due to gusty winds. Always
contact power company before working near
power lines. Assume every power line is live.
Power lines can be blown by the wind. Refer to
Table 1-1 for minimum safe approach distances
between the machine and electrical power lines.
Table 1-1. Minimum Safe Approach Distances
ALWAYS position lift far enough away from power
sources to ensure that no part of the lift can
accidentally reach into an unsafe area.
ALWAYS operate only on a firm and level surface.
NEVER use on surfaces that do not support the
weight of the equipment and its rated load capacity.
ALWAYS keep yourself and all personnel away from
potential pinch or shear points.
ALWAYS report any misuse of equipment to the
proper authorities. Horseplay is prohibited.
ALWAYS maintain good footing on the platform.
NEVER wear slippery soled shoes.
ALWAYS make certain all personnel are clear and
there are no obstructions before repositioning
platform.
Minimum Safe Approach Distance
Voltage Range
(Phase to Phase)
(Feet) (Meters)
0 to 300V
Avoid Contact
Over 300V to 50KV
10
3.05
Over 50KV to 200KV
15
4.60
Over 200KV to 350KV
20
6.10
Over 350KV to 500KV
25
7.62
Over 500KV to 750KV
35
10.67
Over 750KV to 1000KV
45
13.72
Содержание ESP 19
