CR3901-S THE ULTRA-VIEW
™
DX
WARNING! Read the WEIGHT RESTRICTION WARNING, USAGE INSTRUCTIONS
& WARNINGS and FULL-BODY FALL ARREST HARNESS USAGE INSTRUCTIONS
& WARNINGS on pages 4-17 prior to assembly of this product! Failure to follow
the instructions on this page and pages 4-17 may result in serious injury or death!
WARNING! DO NOT over tighten the hardware. Over tightening can lead to
structural damage and may negatively affect the performance of your stand.
Failure to follow these instructions may result in serious injury or death!
Refer to pages 88-95,
Field Installation-Ladderstands
, for installation instructions.
NOTE:
Steps 1-11 require you to temporarily finger tighten nuts to ensure proper
alignment. All bolts should be installed from the inside with nylock nuts on the outside.
STEP 1.
First, attach the
left foot platform
to the
right foot platform
using (3)
1/4" x 2 1/2" hex bolts [L] and (3) 1/4" nylock nuts to secure. (fig. 1)
STEP 2.
Next attach the
top ladder section
and
foot rest
to the
left/right foot
platforms
using (2) 1/4" x 1 3/4" hex bolts [A], (4) nylon washers and (2) 1/4"
nylock nuts. (fig. 1)
STEP 3.
Using (2) 5/16" x 2 1/2" hex bolts [I] and (2) 5/16" nylock nuts attach the
left outer foot platform
to the
left foot platform
. Repeat for right side. (fig. 1)
STEP 4.
Attach the
platform support
to the
left/right foot platforms
using (4)
1/4" x 3" hex bolts [B] and (4) 1/4" nylock nuts.
NOTE:
The
seat hub bracket
on
the
platform support
should be toward the rear of the unit. (fig. 2)
STEP 5.
Attach the
seat hub
to
left/right foot platforms
using (2) 5/16" x 1 3/4"
hex bolts [F] and (2) 5/16" nylock nuts. Then, attach the
seat hub
to the
seat
hub bracket
using (2) 5/16" x 3/4" hex bolts [C]. (fig. 2)
STEP 6.
Insert the
seat post
into the
seat hub.
Then assemble the
seat platform
onto the
seat post
.
NOTE:
(2) 4" nylon washers should be added between
seat post
and
seat hub
and between
seat post
and
seat platform
. Using (2) 5/16" x 1 1/4"
hex bolts [D] and (2) 5/16" nylock nuts attach the
backrest
to the
seat platform
at desired height. (fig. 2)
STEP 7.
Next attach the
platform gussets
to the outside of the
left and right outer
foot platforms
and to the inside of the
top ladder section
using (4) 5/16" x 2 1/4"
hex bolts [H] and (4) 5/16" nylock nuts. (fig. 3)
STEP 8.
Next attach the
left/right under support gussets
to the
platform support
using (2) 5/16" x 1 1/4" hex bolts [D] and (2) 5/16" nylock nuts. Then, attach the
left/right under support gussets
to the outside of the
top ladder section
using (2)
1/4" x 2 1/4" hex bolts [K] and (2) 1/4" nylock nuts. (fig. 3)
STEP 9.
Attach the
rail supports
to the
left and right foot platforms
and
left
and right outer foot platforms
using (8) 5/16" x 1 1/2" hex bolts [E] and (8)
5/16" nylock nuts. Then attach the
rear rail supports
in the same method using
(4) 5/16" x 1 1/2" hex bolts [E] and (4) 5/16" nylock nuts to secure. (fig. 4)
32
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
This Instruction Manual complies with the Treestand Manufacturers Association’s
TMS 04 -
Standard Practice for Treestand Instructions
& TMS 02 -
Standard Test Method for Treestand Fall Arrest Systems
BgTLS0112Ar.QE_StandManual_1/06.QE 1/9/12 3:22 PM Page 32