BIG ASS FANS 8' - 24' Powerfoil Скачать руководство пользователя страница 28

Страница: 28 / 96

8’ - 24’ POWERFOILPLUS™, POWERFOIL™, & WICKERBILL FANS

4. Install Three Remaining Guy Wires

Follow steps 1-3 to install the three remaining guy wires.

CAUTION: The guy wires should be spaced evenly around the fan and

clear of the path the fan blades will rotate.

Evenly cinch all four (4) guy wires into place using the Gripples. The wires

should be taut.

CAUTION: Over-tightening the guy wires could throw the fan off balance.

Once all of the guy wires are taut, secure their loose ends with the wire rope

clips as shown.

Wire Rope Clip

3. Route Guy Wire Through Gripple

Route the guy wire through the Gripple, and the carabiner on the motor frame, and back through the Gripple as shown.

ATTENTION: To back the guy wire out of the Gripple, insert 1/16” (1.5 mm) Allen wrench into the small hole on the Gripple.

ATTENTION: Do not tighten the Gripple until the remaining guy wires have been installed.

Installing Guy Wires (cont.)

Gripple

Содержание 8' - 24' Powerfoil




























































































Результаты поиска

Содержание 8' - 24' Powerfoil

Отзывы:

Похожие инструкции для 8' - 24' Powerfoil

Бренды по названию

Популярные бренды

BIG ASS FANS 8' - 24' Powerfoil, Руководство по установке

Результаты поиска

Содержание 8' - 24' Powerfoil

Отзывы:

Похожие инструкции для 8' - 24' Powerfoil

Бренды по названию

Популярные бренды