Bierer DCI-50-CT Скачать руководство пользователя страница 2

 

 

CAUTION 

The  equipment  covered  in  these  operating  instructions  should  be  used  by 
qualified  employees,  trained  in  and  familiar  with  the  safety-related  work 
practices,  safety  rules  and  other  safety  requirements  associated  with  the  use  of 
this  type  of  equipment.    These  instructions  are  not  intended  as  a  substitute  for 
adequate  training,  nor  do  they  cover  all  details  or  situations  which  could  be 
encountered in relation to the operation of this type of equipment. 

NOTICE 

Before  operating  this  equipment,  read,  understand  and  follow  all  instructions 
contained in this manual.  Keep instructions with equipment. 

 

 

DANGER 

 

DO NOT ATTACH TO ENERGIZED SOURCE. 

 

WARNING

 

Make  sure  the  battery  is  removed  any  time  unit  is  not  in  use  or 
stored in the bag. Failure to do so could result in a fire hazard. 
 

 

WARNING

 

Always install and remove the CT with the unit off. 

Never clamp CT around a conductor until connected to unit.

 

Limitation of Warranty and Liability 

Bierer & Associates Inc. warrants this product to be free from defects in workmanship 
and material, under normal use and service conditions for a period of one year from date 
of shipment. 

Due to continuous product improvement and development, Bierer & Associates Inc. 
reserves the right to modify product designs and specifications without notice. 

It  is  impossible  to  eliminate  all  risks  associated  with  the  use  of  high  voltage  electrical 
devices  including  this  device.    Risks  of  serious  injury  or  death  are  inherent  in  working 
around energized electrical systems.  Such risks include but are not limited to variations 
of  electrical  systems  and  equipment,  manner  of  use  or  applications,  weather  and 
environmental conditions, operator mentality, and other unknown factors that are beyond 
the control of Bierer & Associates Inc. 
Bierer & Associates Inc. does not express or imply to be an insurer of these risks, and by 
purchasing  or  using  this  product  you 

AGREE  TO  ACCEPT  THESE  RISKS. 

IN  NO 

EVENT  SHALL  Bierer  &  Associates  Inc.  BE  LIABLE  FOR  ANY  INCIDENTAL, 
CONSEQUENTIAL  OR  SPECIAL  DAMAGES  RESULTING  FROM  THE  USE  OR 
HANDLING OF THIS PRODUCT. 

Содержание DCI-50-CT









Отзывы: