manualshive.com logo in svg

Biasi Activ A 25C, Руководство пользователя и инструкции по установке

Поделиться
Скачать
Biasi Activ A 25C Скачать руководство пользователя страница 72

- 72 -

MAINTENANCE

MAINTENANCE

 MAINTENANCE

9 

Warnings

9.1 

The procedures detailed in this chapter 

must be carried out only by a profes-
sionally qualifi ed  person

. Thus you are 

advised to contact an Authorised Service 
Agent. 

For Ireland (IE), the servicing work must 
be carried out by a competent Person. 

For effi cient and continuous operation of the 
boiler you are advised to have, at least once 
a year, maintenance and cleaning done by 
an Approved Service Engineer. 

Isolate the appliance from the electricity 
supply

 by turning off the fused spur isola-

tion switch adjacent to the appliance and 
turn off the gas cock, before carrying out 
any procedures, whatsoever, for cleaning, 
maintenance, opening or dismantling boiler 
panels. The Engineer should complete the 
Service Interval Record at the back of the 
manual.

 Dismantling the external pan-

9.2 

els

Front panel

Unscrew screws  

• A 

 

and remove the front 

panel  D  by pulling it and pushing it towards 
the top so that it is freed from the top hous-
ings ( Fig. 9.1  and  Fig. 9.2 ).

Side panels

Loosen screws " 

 

B 

 -

 

 

F 

 

"

 

and "  C  

-

 

 

H 

 

"

 

in  Fig. 

9.1  and remove the two side panels  E  and 
 G  by pulling towards the outside.

 

Fig. 9.1

  

A 

  

B 

  

C 

  

D 

  

E 

  

F 

  

G 

  

H 

  

Fig. 9.2

Содержание Activ A 25C

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды