background image

   page 6 

        

Installation and Operation Guide 

NPX

OPERATION (CONTINUED)

Paging and Message Playback Instructions

Make a live page

1. At the Page Code screen press the top or middle LCD buttons next to

to navigate to and highlight a specific page code. The user may also

type the appropriate page code number on the keypad (10-key only).

2. Press and hold the PTT button, speak into the microphone and release

the button when done. On gooseneck models the user may also tap the

latching button, speak into the microphone and tap the button when done.

Target rings around the microphone icon allow the user to see when the 

optimal speaking level is reached:

Levels

Status

The microphone icon displays when the user presses and 

holds the PTT button or taps the latching button. The green ring 

displays and flashes until the user speaks into the microphone.  

When the user speaks into the microphone, the outer green ring 

displays once the optimal speaking level is reached. The user 

may need to move closer to the microphone or speak louder.
If the speaking level gets too loud the outer ring turns red. The 

user must move away from the microphone or speak more 

quietly to get to an acceptable level. 

Playback a recorded message

3. At the Page Code screen press the top or middle LCD buttons next to

to navigate to and highlight a specific page code. The user may also

type the appropriate page code number on the keypad (10-key only).

4. Press and hold the PTT button, speak into the microphone to record the

message and release the button when done. On gooseneck models the

user may also tap the latching button, speak into the microphone to record

the message and tap the button when done.

Preambles

Live page and recorded message playbacks can be preceded by a preamble. 

The preamble plays first when the user presses and holds the PTT button or 

taps the latching button. The user can then make the live page or the recorded 

message plays back immediately after.

Figure 16: Live Page after Preamble

Page Failed

When a higher priority page code is already in progress. If any zones defined in 

the page zone are available (even if some zones are busy) the paging station 

will allow the page to the available zones.

Playback Failed

The playback failed screen displays when the user tries to playback a message 

with a non-existent recording.

Navigation

See the 

Navigation Table

 for LCD navigation during paging activities and 

LCD 

Icons

 for descriptions.

Figure 15: Preamble Playing

Содержание NPX G1040
















Отзывы: