BH FITNESS G160, Инструкция по сборке и эксплуатации

Страница: 16 / 30

16
8 .- Place the disc supports (22) on both sides of the bar
(61) and fix them with the screws (116), Fig.8.
Remove the bolts (119) of the welding piece (13) and adjust
the distance between the hooks on both sides. Refit the
screws (119), Fig.8B.
Place the bushing (19) on the right support (17) and fix it
with the screws (114), the washers (103), and the nuts
(100), Fig.8A.
Follow the same steps for the left side.
9 .- Place the bars (45) on the horizontal tube (2), place the
supports (33), the cushions (70), the weights (94) and the
upper weight (93), Fig.9.
Attach the selector (90) on the upper weight (93). Insert the
selector (90) into the lower weights (94), Fig.9.
Screw the pulley (27) into the upper weight (93), Fig.9.
10 .- Pass the cable (58) from the pulley (B) to the pulley (I)
as shown on Fig.10.
First fix the pulley (B) using the screw (112), the washers
(103) and the nut (100), Fig.10. Pulleys (E), (F), (G) are
installed in the same way. Fix the pulley (C) using the screw
(109), the bushing (46) and the nut (100).
To install pulley (D), (H) first fit pulley bracket (34) using the
screw (119) and the bushing (73) and then use the screw
(112), the washers (103) and the nut (100) to fix the bracket
and the pulley, Fig.10.
To install the pulley (I) fix the support (34) with the screw
(119) and the nut (73). Fix the pulley (I) with the screw
(113), the washers (103) and the nut (100), Fig.10.
Fix the end of the cable to the pulley of the slider and attach
it with the screw (130), the washer (103) and the nut (100),
Fig.10.
Follow the same steps to attach the cable to the other side.
11 .- Place the right-side cover (42) on the rear tube (10) as
shown on Fig.11 and fit the screws (122) and the washers
(95).
Place the supports (91) on the right side of the rear tube
(10) and fit the screws (116) and the washers (103), Fig.11.
Place the covers (71) on the supports (91) and tighten the
cover screws.
Follow the same steps for the left side.
12 .- Place the left front cover (39) and fit the screws (122)
and the washers (95), Fig.12.
Place the middle cover (38) and fix it to the upper (36) and
lower plates using the screws (122) and the washers (95),
Fig.12.
Place the right front cover (40) and fit the screws (122) and
the washers (95), Fig.12.
Fit the screws (104) and the washers (97), Fig.12.
13 .- First lock the rear covers (37) together using the
screws (104) and the nuts (97). Attach the hook (137) to the
rear cover (37) using the screws (134) and the nuts (100),
Fig.13. Place the rear covers (37) and fix them to the side
covers (41), (42) using the screws (122) and the washers
(95), Fig.13.
14 .- Place the side covers (43) as shown on Fig.14 and fit
the screws (104) and the washers (95).
Pass the cable (58) through the cover (60) and insert it to
the shaft (59), place the hook (72), Fig.14.
15 .- Place the handlebar (26) on the adjustment bar (8) and
turn it 90º as shown on Fig.15.1.
Place the inner cover (77), the foam (75) and the outer
cover (76) on the leg tube (29) and fix it with the screws
(118), Fig.15, A.
Attach the frame (28) to the tube (29) and fit the screw
(107), the washer (103) and the nut (100), Fig.15, A.
Place the frame (28) on the adjustment bar (8) and turn it
90º as shown on Fig.15.2.
Do not hesitate to get touch with the Technical Assistance
Service if you have any queries by phoning customer
services (see last page in manual).
BH RESERVES THE RIGHT TO MODIFY THE
SPECIFICATIONS OF ITS PRODUCTS WITHOUT
PRIOR NOTICE.