manualshive.com logo in svg

BEWATOR COTAG 4101-2, Руководство по установке, Страница: 84 / 158

Поделиться
Скачать
BEWATOR COTAG 4101-2 Скачать руководство пользователя страница 84

4101-2 Controller Installation Handbook

8-16

Connecting a Comms module to a modem at a remote site

The modem is connected to the upstream (CONN2) RS232
connections of the Comms module. Note that there is also one
connection from the modem to the downstream (CONN3) DCD
connection on the Comms module (shown in bold below). The modem
has a 25-way D-type connector.

Comms module

Modem

u/s TXD (CONN2) TXD (pin 2)
u/s RXD (CONN2) RXD (pin 3)
u/s CTS (CONN2) CTS (pin 4) - see diagram below
u/s RTS (CONN2) RTS (pin 5) - see diagram below
d/s DCD (CONN3) DSR (pin 6)
u/s SE (CONN2)

SE (pin 7)

u/s DCD (CONN2) DCD (pin 8)
u/s DTR (CONN2) DTR (pin 20)

Note: CTS and RTS should be linked together both at the modem and
at the Comms module as shown in the diagrams below.

Comms module

Connect cable screen

to Controller case

u/s TXD

u/s RXD

u/s CTS
u/s RTS

d/s DCD

u/s SE

u/s DCD

u/s DTR

Modem: 25-way D-type

2

TXD

3

RXD

4

CTS

5

RTS

6

DSR

7

SE

8

DCD

20

DTR

Modem: 25-way D-type
2

TXD

3

RXD

4

CTS

5

RTS

6

DSR

7

SE

8

DCD

20

DTR

TXD CTS RTS DCDDTR SE

Scr RXD TXD CTS RTS DCD DTR SE

232 232

RXD

Scr

CONN2

CONN3

Comms

Module

The modem signals are as follows:

TXD

 - control and data signals passing from Comms module to

modem.

Содержание 4101-2































































































































































Отзывы:

Нет отзывов