BEWATOR COTAG 4101-2 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 158

BEWATOR COTAG 4101-2 Скачать руководство пользователя страница 33

4101-2 Modular Controller

3-9

Controller case at one end only. Signal Earth not required. If the
Comms module is plugged into this Controller then connect CONN2
to both the Comms module and to CONN2 of next Controller - see
Comms module installation note.

Pin

Function

Connection

No connection

connect cable screens to Controller case

RX

R

to RX on Controller, TX on Comms module

RX

Receive -

to RX on Controller, TX on Comms module

TX

Tr

to TX on Controller, RX on Comms module

TX

Transmit -

to TX on Controller, RX on Comms module

0V

Signal Earth

no connection to Signal Earth required

Note

: to pass emission regulations, the RS485 cable must pass

through the ferrite sleeve provided, see the chapter on “Earthing and
screening”.

Master/slave connection (no Comms module)

:

Connect CONN2 RX, RX , TX and TX pins on the master Controller
to their opposite pins on the slave Controller. Connect cable screens
to Controller case at one end only. Signal Earth not required.

Pin

Function

Connection

No connection

connect cable screens to Controller case

RX

R

connect RX on master to TX on slave

RX

Receive -

connect RX on master to TX on slave

TX

Tr

connect TX on master to RX on slave

TX

Transmit -

connect TX on master to RX on slave

0V

Signal Earth

no connection to Signal Earth required

Note

: to pass emission regulations, the RS485 cable must pass

through the ferrite sleeve provided, see the chapter on “Earthing and
screening”.

CONN3

Function

: general connections. The POWER and STATUS LEDs and

TAMPER switch for the cover are already connected when you receive
the Controller. Each function uses two terminals on the connector.

Pin

Function

POWER LED

Indicates power on motherboard via LED visible through cover.

STATUS LED

Indicates processor running via flashing LED visible through cover.

TAMPER

Input indicating cover is opened. Connected to switch on cover. Can
also be connected in parallel to switch on power supply unit cover.
Input is normally open circuit. Short circuit indicates cover removed -
alarm sent to computer.

PSU MON

Input indicating mains failure. Input is normally closed circuit. Open
circuit indicates mains failure - alarm sent to computer.

«
...
31
32
33
34
35
...
»

Содержание 4101-2































































































































































Отзывы:

Нет отзывов