BEWATOR COTAG 4101-2 Скачать руководство пользователя страница 157 | Manualshive

Страница: 157 / 158

BEWATOR COTAG 4101-2 Скачать руководство пользователя страница 157

A-3-1

Appendix 3

Wiring and setting up a door for

anti-passback

Local anti-passback

Local anti-passback enables you to designate Access Points as “In
Readers” or “OUT Readers”. When both an IN Reader and an OUT
Reader control the same door, the readers have to be wired and
configured in a certain way.

Wiring

1.

The DO and

Ø

V connections for the IN Reader should be wired

in parallel with the DO and

Ø

V connections for the OUT

Reader, and should be connected to the door monitoring
switch.

2.

The door lock relay for either the IN Reader or the OUT Reader

must be able to unlock the door. This means that with a fail
secure (power to unlock) mechanism, the relays must be wired
to the lock in parallel. With a fail safe (remove power to unlock)
mechanism, the relays must be wired to the lock in series.

3.

The door exit control inputs (egress) must not be connected.

Configuring

1.

Door monitoring should be Enabled on both the IN Reader and

the OUT Reader (select the check box labelled

Enable Door

Contact Monitoring

on the

Monitoring Actions

page in the

access point records).

2.

Door Forced and Door Open should be Enabled on one reader

and Disabled on the other reader (it doesn’t matter which way
round). (The check boxes are

Door

Forced Alarm

and

Door

Open Alarm

on the

Monitoring Actions

page in the access

point records.)

3.

One reader must be configured as an IN Reader and the other

must be configured as an OUT Reader in the Local Anti-
Passback section of the

Monitoring Actions

page in the

access point records.

«
...
155
156
157
158
»

Содержание 4101-2































































































































































Отзывы:

Нет отзывов