22
disease, age, physical predisposition, excessive use of
stimulants, stress or lack of sleep. Arrhythmia can only be
ascertained through examination by your doctor.
Repeat the measurement if the flashing icon
is dis-
played after the measurement. Please note that you should
rest for 5 minutes between measurements and not talk or
move during the measurement. If the icon
appears
often, please contact your doctor. Any self-diagnosis and
treatment based on the test results may be dangerous. It is
vital to follow your doctor’s instructions.
Risk indicator:
The measurements can be classified and evaluated in ac-
cordance with the following table.
However, these standard values serve only as a general
guideline, as the individual blood pressure varies in different
people and different age groups etc.
It is important to consult your doctor regularly for advice.
Your doctor will tell you your individual values for normal
blood pressure as well as the value above which your blood
pressure is classified as dangerous.
The classification on the display and the scale on the unit
show which category the recorded blood pressure values
fall into. If the values of systole and diastole fall into two dif-
ferent categories (e.g. systole in the ‚High normal‘ category
and diastole in the ‚Normal‘ category), the graphical classi-
fication on the device always shows the higher category; for
the example given this would be ‚High normal‘.
Blood pressure
value category
Systole
(in mmHg)
Diastole
(in mmHg)
Action
Setting 3:
severe
hypertension
≥ 180
≥ 110
seek medical
attention
Setting 2:
moderate
hypertension
160 – 179 100 – 109
seek medical
attention
Setting 1:
mild
hypertension
140 – 159 90 – 99
regular monito-
ring by doctor
High normal
130 – 139 85 – 89
regular monito-
ring by doctor
Normal
120 – 129 80 – 84
self-monitoring
Optimal
< 120
< 80
self-monitoring
Source: WHO, 1999 (World Health Organization)
8. Error messages/troubleshooting
In case of faults, the _ message appears in the display.
• Error messages may appear if:
• systolic or diastolic pressure could not be measured (
or
appears on the display)
• systolic or diastolic pressure was outside the measure-
ment range (“
Hi
” or “
Lo
” appears on the display)
• the cuff is fastened too tightly or loosely (
or
ap-
pears on the display)
Содержание 65905
