Better Packages 555e Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 46

Better Packages 555e Скачать руководство пользователя страница 25

Rev 9 2022

25

Maintenance & Repair

Solenoid Replacement

11. Pull the connector and wire through the frame

of the machine

12. Pull the plunger from the solenoid

13. Remove 4 screws from the solenoid shelf

14. Remove the nut holding the solenoid plunger

15. On new solenoid shelf partially insert the back 2

screws so it can hang freely

16. Install the new plunger

17. Reinsert the plunger into the solenoid body

18. Align the solenoid shelf and replace the 2

front screws

19. Tighten down all screws on the solenoid shelf

20. Reinstall the spring

21. Replace the access plate

22. Reinstall the baffle safety

23. Snap the tank shelf back into place

24. Replace the right cover (5 Philips screws)

25. On left cover plug keypad ribbons back into

controller board

a. Be sure not to miss any pins as this will effect

the length selected

26. Reinstall left cover be sure not to pinch or drive a

screw through the keypad ribbons.

27. Replace water tank, brushes, and water bottle

Continued

«
...
23
24
25
26
27
...
»

Содержание 555e















































Отзывы:

Нет отзывов