Better Packages 555e Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 46

Better Packages 555e Скачать руководство пользователя страница 22

22
Rev 9 2022

If your machine is making an electronic grinding noise when the tape is dispensing from the machine more often than

not it is the solenoid that controls the cutter yoke assembly having dirty contacts. This is a relatively simple procedure

that can be accomplished within an hour for someone with no experience and the right tools. If this process is followed

and the noise persists please contact

Better Packages

Machinery Support at (813) 345-3070

Part Numbers

•

E55504801 – Solenoid Shelf Assembly

Tools Needed

• Philips head screwdriver

• 80 Grit Sandpaper

Maintenance & Repair

Solenoid Repair

Procedure

1. Unplug Machine

2. Remove the water bottle, and tank assembly

3. Remove right side cover (5 Philips screws)

4. Remove left side cover (5 Philips screws) be

careful as the ribbons connecting the keypad can

be ripped easily.

5. Unplug keypad ribbons from controller board

6. Remove the tank shelf (gray plastic housing

bottom front of machine) by pulling down on the

top while pressing in on the side retaining clips.

7. Remove the Baffle Safety (2 or 3 Philips screws

depending on model)

8. Remove the access plate (2 Philips screws)

a. Depending on the age of your machine the

access plate and solenoid shelf might be a

single piece

9. Remove the center spring

a. Clean out any tape debris

10. Remove front 2 screws (labeled A) from the

solenoid shelf and loosen the back 2 screws

(labeled B) allowing it to pivot

A

B

«
...
20
21
22
23
24
...
»

Содержание 555e















































Отзывы:

Нет отзывов