Better Packages 555e Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 46

background image

16
Rev 9 2022

Maintenance & Repair

Feed Wheel/

Blade Height Adjustment

When a dispense key is pressed the tape cutter blade and the lower feed wheel lift up. The machine has an adjustment

set screw that sets the height of the blade and lower feed wheel. The adjustment sets the amount of pinch force

between the upper and lower feed wheels. If the feed wheel does not grip the tape sufficiently, the tape can slip. When

the tape slips an inaccurate measurement of the tape length occurs, resulting in a shorter than normal tape piece. If

short or erratic tape lengths occur, the adjustment described below may need to be performed to correct the problem.

Tools needed

• 3/32” Allen wrench 4” long at minimum

Procedure

1. Unplug the machine

2. Open the top cover

3. Install the tape fully

4. On the right side of the feed wheel, lift up on the

lever (Figure 18-1)

5. Test the tension on the tape by pulling the tape

out from the back of the feed wheel see Figure

18-2 for direction

a. If tape is removed easily with little to no

resistance the feed wheel will need to be

tightened (clockwise)

b. If tape is very difficult to remove the

feed wheel will need to be loosened

(counterclockwise)

6. Move the lever back to its home position and

remove the tape from the machine

Figure 18-1

Figure 18-2

Figure 18-3

7. Turn the machine around so you are looking into

the cavity where the tape roll sits

8. Locate the feed wheel adjustment access hole, it

will be between the slide guides (Figure 18-3)

9. Use a 3/32” Allen wrench to make the needed

adjustments from step 4

a. Tighten or loosen in half turn

increments

10. Insert a strip of tape under the feed wheel and

lift up on the lever

11. Pull the tape out from under the feed wheel.

b. Proper tension is achieved when the tape is

pulled taught and can be removed with a fair

amount of resistance

a. If this is not how it feels repeat steps

8 through 10 until proper tension is

achieved

«
...
14
15
16
17
18
...
»

Содержание 555e















































Отзывы:

Нет отзывов

Похожие инструкции для 555e

Бренд: Fast & Fluid Management Страницы: 18

Бренд: Tach-It Страницы: 8

Бренд: Salter Brecknell Страницы: 36

Бренд: WaterLogic Страницы: 84

Бренд: Atmospheric Water Systems Страницы: 46

Бренд: ScaleBlaster Страницы: 8

Бренд: Coca-Cola Страницы: 24

Бренд: First Sales Страницы: 27

Бренд: U-Line Страницы: 2

Profile SmartWater PNSF31Z

Бренд: GE Страницы: 3

SmartWater GXCC01D

Бренд: GE Страницы: 24

SmartWater GNSF35Z

Бренд: GE Страницы: 28

Бренд: Crystal Mountain Страницы: 47

Бренд: IBC Water Страницы: 33

Бренд: Breville Страницы: 16

Бренд: Hydropath Страницы: 12

Бренд: Kraus Страницы: 12

Бренд: Manitowoc Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды