manualshive.com logo in svg

Bettcher Whizard 210, Инструкция по эксплуатации и список запасных частей

Поделиться
Скачать
Bettcher Whizard 210 Скачать руководство пользователя страница 14

Operating 

BETTCHER                      Whizard

®

 Universal Blade Sharpener Model 210, 115V 

Instructions 

INDUSTRIES, INC.                                                                       Rev. 05/17/2019 

Page 10 

8.7  Sharpening The Blade  (Continued) 

 

With a continuous spark appearing for 

complete

 

revolutions  

of the blade, proceed to steel the blade edges as described below. 

 

For Model 360/505/625/850/880/350 Cone/TRIMVAC

®

/TRIMVAC

®

18AMX Blades: 

 

With your right hand, grasp the knob of the steeling device (#6) between your 
middle and index fingers. 
 
Swing steeling device toward the center of the blade. 
 
Slide the steeling device to the right until the steeling shaft contacts the inside 
blade edge. 
 
Hold the steeling device 

lightly

 against the blade for a few complete blade 

revolutions. 
 
Simultaneously  release  the  steeling  device  from  the  blade  edge  and  back  off  the 
grinder with your left hand. 
 
Swing steeling device out away from the blade. 
 
Turn off blade motor switch (#2) and grinder motor switch (#3). 

 

For Model 350/500/520/564/620/750/754/900/1040/1200/1000/1300/1400 
and 1500 Blades: 

 

With your right hand, grasp the knob of the steeling device (#6) between your 
middle and index fingers. 
 
Swing the steeling device toward the center of the blade. 
 
Press down on steeling shaft knob (#7) with your thumb and slide the steeling 
device to the right until the steeling shaft contacts the inside blade edge. 
 
 

COMPANY 

CONFIDENTIAL

Содержание Whizard 210



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды