manualshive.com logo in svg

Bettcher Whizard 210, Инструкция по эксплуатации и список запасных частей

Поделиться
Скачать
Bettcher Whizard 210 Скачать руководство пользователя страница 12

Operating 

BETTCHER                      Whizard

®

 Universal Blade Sharpener Model 210, 115V 

Instructions 

INDUSTRIES, INC.                                                                       Rev. 05/17/2019 

Page 8 

8.3  Installing Blade Into Blade Holder  (Continued) 
 
Check that blade is secure in the blade holder. 
 

Note: 

If blade turns freely in blade holder with hold down pins  

in place, it is worn excessively and will not operate  

at maximum efficiency in your Whizard

®

 knife.   

This blade can not be sharpened and should be discarded. 

 

8.4  Grinder Feed Control 
 
Turning the pedestal knob (#8) clockwise feeds the grinder wheel (#13) into 
the blade and counterclockwise moves the grinder wheel away from the blade. 

 

8.5  Positioning Grinder To Sharpen Blade 

 

Loosen nut on positioner plate (#9) and align mark on positioner arm (#9A) 
with mark on positioner plate (refer to "Position-Model" label on positioner 
plate), then retighten nut.  Holding the grinder pivot (#11) with your left hand, 
press  in  the  knob  of  the  positioner  shaft  (#10)  and  lift  the  grinder  (#12) 
upward, allowing the positioner shaft to enter the slot of positioner arm (#9A).  
Release positioner shaft into hole of the positioner arm. 

 

Note: 

  

Back away grinder as needed when raising  

into position to avoid hitting the blade. 

 

DO NOT lift grinder into position with the motor turned on. 

 

8.6  Grinder Wheel 
 
This  grinder  wheel  is  a  CBN  (Borazon)  plated  wheel-form  and 

does not

 

require dressing of its grinding surfaces.  See Section 9.0 for cleaning. 
 
 

 

COMPANY 

CONFIDENTIAL

Содержание Whizard 210



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды