background image

 

Installation Guide for Betta 7000 Straight Drop Awning  
with Wire Guide and Semi Cassette 

 

Please Note: These instructions should be read thoroughly before installing. 

 

This  is  a  guide  to  assist  in  the  installation  and  care  of  your  external  awnings.  Betta  Blinds  and  Awnings  do  not 
guarantee the accuracy of the information contained in this guide. We recommend an experienced expert installer 
to rely upon their own skills. This is based on general knowledge concerning the assembly, materials and working 
process of  the external  blinds,  which  is  known  to  us at  the  time  of  printing  this guide,  consequently,  is  subject  to 
change and Betta Blinds and Awnings specifically reserves the right to change this guide without notification. 

 

Ensure all components are included in your packaging, before proceeding to install: 

  Universal brackets x 2 
  Gearbox 
  Blind  
  Wire cable x 2 
  Rapid Lock 15mm & 35mm x 2 
  Release Key x 1  
  Barrel Nut x 2 
  Nut x 6 

 

  L  Bracket  or  Deck  hinge,  (whichever  is 

required) 

  Crank handle 

(if required)

 

  Split pin x 1 
  Pivot pin and plate with nut and bolt 
  Latch & Saddle 

(if required)

 

  Nut & Bolt for gear x 2 each 
  Semi Cassette 

 

 
You  will  also  need:  Screws,  plugs,  Philips  head  screwdriver, good  quality  wire  snips,  drill,  hammer  drill  (if  drilling 
into concrete), measuring tape and spirit level 

 

If installing on a brick wall NEVER put the screw into a mortar line.

 If the position, you need to drill is over a 

mortar line move up to the centre of the brick above that position. 

 

Check the size of your blind against the label, which will be attached to the packaging, or it could be on the blind.  

 

Fitting the Semi Cassette Pelmet 

 

 

1. 

Remove the awning from the pelmet.

  

 

 

2.  Measure  the  width  of  the  hood  then  the  width  of  the  window.  The  difference  between  the  two  is  the  total 

amount of overhang your box will have. Divide this number by two to determine how much overhang you will 
have on each side. E.g. If the hood measures 2300 and the window measures 2000, the total overhang will be 
300mm. dividing by two equals 150mm each side of the window.  

 

3.  Pre-drill the holes for the Pelmet as per the desired fixing points below. 

 
 

        

 

4.  Carefully raise the Pelmet into position ensuring that it is horizontal. Mark the holes  

 

5.  Pre-drill all holes and plug. When all holes are drilled, carefully position the pelmet, and fasten with screws. 

 

 

Содержание 7000












Отзывы: