background image

 

 

 

Please see Video: How to attach & remove the wire 

https://www.loom.com/share/a7222d33554c4650ae89500856510d70

 

 

8.  Attach the Barrel Nut to the bracket and then add the top Rapid Lock and fasten the nut, allow for extra thread 

for adjustment when the bottom Rapid Lock is assembled. 

 

 

9. 

Install Bottom L Brackets at the bottom fixing point.  

    

 

     

 

10.  Feed cable through end caps on the bottom rail. 

 

11.  Fasten the 15mm Rapid Lock on to the L Bracket, then pull wire taut and cut the wire approximately halfway 

along the 15mm Rapid Lock as below picture demonstrates. Then repeat step 7 and step 8 to finish installing 
the  bottom  Rapid  Lock.  With  top  and  bottom  Rapid  Locks  in  place  make  final  tension  adjustments  by 
tightening either top or bottom nut 

 

 

 

NOTE:

 If Deck hinges are used, first fasten the 15mm Rapid Lock onto Deck hinge then repeat step 7 and step 8 to 

assemble top Rapid Lock. The wire will be cut approximately halfway along the 30mm Rapid Lock. 

 

12. 

Insert crank handle into eyelet and wind your blind down. 

 

 

13. 

If 

you’re  using  lockdown  latches  position  saddles  where  required  and  attach  to  bottom  fixing  point 

refer  to 

picture below.  See below if the awning has a valance. 

Содержание 7000












Отзывы: