4
90º
90º
CHOOSE THE CORRECT LOCATION
The surface chosen to install the pool must respect the following
technical characteristics:
1. Because of the combined weight of the water inside the pool
and the pool users, it is extremely important that the surface
chosen to install the pool is capable of uniformly supporting
the total weight for the entire time the pool is installed. When
choosing the surface, take into consideration that water may
come out of the pool when in use or in the rain. If the water
softens the surface, it may lose its capability to support the
pool weight.
2. Check regularly the position of the vertical legs and the
U-supports. They must be on the same level as the bottom of
the pool at all times. If the vertical leg or the U-support starts
to sink into the ground, drain the water immediately to avoid
the pool collapsing due to the uneven loading on the frame
structure. Change the location of the pool or modify the
surface material.
3. We recommend positioning the pool away from any objects
children could use to climb into the pool.
4. Position the pool near an adequate drainage system to deal
with overflow or to discharge the pool.
5. The surface must be flat and smooth. If the surface is
inclined or uneven, it can create an unbalanced loading on
the structure of the pool. This situation can damage the
welding point of the liner and bend the frame. In the worst
cases, the pool can collapse, causing serious personal injury
and/or damage to personal property.
6. The selected surface must be clear of any type of object.
Due to the weight of the water, any object under the pool
could damage or perforate the bottom of the pool.
7. The selected surface must be clear of aggressive plants and
weed species. Those types of strong vegetation could grow
through the liner and create water leakage. The grass or
other vegetation that may cause odor or slime to develop
have to be eliminated from the set-up location.
8. The selected location must not have overhead power lines or
trees. Be sure the location does not contain underground
utility pipes, lines or cables of any kind.
9. The selected position must be far from house entrance. Do
not position any equipment or other furniture around the pool.
The water that comes out of the pool during the use or due to
a faulty product can damage the furniture inside the house or
surrounding the pool.
10. The selected surface must be flat and without holes that can
damage the material of the liner.
Follow the important instructions above to choose the correct
surface and location to set up your pool. Damaged parts of the
pool, due to the fact that the set-up surface and location does not
match the instructions, will not be considered as manufacture
defect and will avoid the warranty and any service claims.
Suggested set-up surfaces:
grass, ground, concrete, and all other surfaces that respect the above set-up conditions.
Not suggested surfaces:
mud, sand, gravel, deck, balcony, driveway, platform, soft/loose soil or other surface that does not meet the
above set-up conditions.
NOTE:
Check with your local city council for by-laws relating to fencing, barriers, lighting and safety requirements and ensure you
comply with all laws.
NOTE:
If have a filter pump, refer to the pump’s manual for instructions.
NOTE:
The ladder must match the pool size and should be used only for entering and exiting the pool. It is forbidden to exceed the
permitted payload of the ladder. Check regularly if the ladder is properly assembled.
POOL MAINTENANCE
If you do not adhere to the maintenance guidelines below, your health might be at risk, especially that of your children.
Using chemical tablets (not included):
NOTE:
Chemconnect or Chemical Floater must be used when you perform chemical maintenance with tablets. Your purchased item
may not include any of those dispensers, in this case you can purchase it by visiting our website www.bestwaycorp.com or at the
nearest pool dealer.
After the installation of the pool's steel frame is completed, ensure that the verticals are perpendicular to the ground. If they
aren’t, the verticals could be bent or deformed.
Nachdem der Stahlrahmen des Pools aufgebaut wurde, überprüfen, ob die vertikalen Stangen genau senkrecht auf dem Boden
stehen. Wenn nicht, könnten sie verbogen oder deformiert werden.
Controleer nadat de installatie van het stalen frame van het zwembad is voltooid of de verticale delen loodrecht op de grond
staan. Als dat niet het geval is, kunnen de verticale delen verbogen of vervormd raken.
Quand l’installation de la structure en acier de la piscine est terminée, assurez-vous que les éléments verticaux sont
perpendiculaires au sol. Si ce n’est pas le cas, les éléments verticaux pourraient être tordus ou déformés.
EN
DE
NL
FR
Do not assemble with pool legs on soft lawn. If you must assemble the pool on a soft surface, timber boards (not included)
must be placed under the feet of the vertical support rods for even weight distribution.
The timber board must meet two conditions:
1). The thickness is less than 1cm.
2). The board should not touch the pool liner.
Den Pool nicht mit den Poolfüßen auf weichem Rasen montieren. Falls Sie die Montage des Pools auf einer weichen Fläche
durchführen wollen, müssen Bretter (nicht enthalten) unter den Füßen der senkrechten Stützen platziert werden, um die
Traglast zu verteilen.
Die Holzbretter müssen folgende Bedingungen erfüllen:
1). Stärke: höchstens 1 cm.
2). Das Brett darf den Poolliner nicht berühren.
Niet monteren met de zwembadpoten op een zacht grasveld. Als u het zwembad op een zacht oppervlak moet monteren,
moeten houten platen (niet inbegrepen) onder de poten van de verticale draagsteunen geplaatst worden om het gewicht te
verdelen.
De houten plaat moet aan twee voorwaarden voldoen:
1). De dikte moet minder dan 1 cm zijn.
2). De plaat mag de zwembadbekleding niet raken.
Ne montez pas les pieds de la piscine sur une pelouse qui s’enfonce. Si vous devez monter la piscine sur une surface molle, il
faut placer des planches en bois (non fournies) sous les pieds des tiges de support verticales pour répartir la charge.
Les planches en bois doivent respecter les deux conditions suivantes :
1). Une épaisseur inférieure à 1 cm.
2). La planche ne doit pas entrer en contact avec la bâche de la piscine.
EN
DE
NL
FR
