Best Power Unity/I UT3K Скачать руководство пользователя страница 9

Страница: 9 / 12

UTY 618

RESTRICTED

November 1995

Figure 3: Battery Tray, Front View

200-4.

Use the two bolts to attach the battery tray handle to the battery tray at the front of
the unit (see Figure 3).

200-5.

Remove the bolt from the top DC connector. See Figure 3 for DC connector location.

200-6.

Disconnect the top DC connector as shown in Figure 3.

200-7.

If the unit has external batteries, perform the following steps:

a. Switch off the DC disconnect switch on the external battery cabinet(s).

b. Disconnect the external battery cable (+) from the “+BATT” post at top of the

fuse board (see Figure 3). Insulate the cable lead with electrical tape or heat
shrink tubing.

200-8.

In the order listed, disconnect the following from the fuse board. Remove any tie
wraps. See Figure 3 for connection locations.

a. Fast-on connector from E5.
b. Connector from J3.
c. Connector from J1.

200-9.

Pull the battery tray out just far enough to expose the first battery.

200-10.

Disconnect the negative (–) battery cable from the first battery.
Insulate the cable lead with electrical tape or heat shrink tubing.

Содержание Unity/I UT3K












