Best Fitness BFT2, Руководство пользователя

Страница: 25 / 34

25
MainTenance
LUBRICATING THE DECK
A well lubricated deck will ensure high performance of your treadmill and reduce the level of normal
wear and tear to important components. This treadmill has been pre-lubed at the factory. There
is no need to apply any lubricant in order to start to use your new treadmill. However, for optimal
performance, the running deck may require periodic lubrication. With average usage (30 minute
workout session at 3-4 mph, 3 times a week, for two people) lubricate every four to six months. You
may adjust the timing of the lubrication based on the intensity of the treadmill use level.
To check the lubrication level, simply lift the running belt, and put your hand as far into the center
of the belt as you can reach. If your hand shows signs of silicone (some wetness), then it does not
need additional lubrication. If the board feels dry and there is very little evidence of silicone on your
hand, then additional lubrication should be added.
TO LUBRICATE THE DECK:
1. Stop the running belt so that the belt’s seam is located on
top and in the center of the deck.
2. Unplug the treadmill from the electrical outlet.
3. Prepare the lubricant by removing the cap.
4. Lift the running belt.
5. Position the lubricant’s nozzle between the belt and the
board at approximately 200mm (8”) from the front of the
treadmill.
6. Apply the silicon from the front to the rear of the treadmill
from both the left and right side of the treadmill.
Try to reach as far into the center of the running deck as
possible.
7. The silicone should be applied in drops or in a very thin
stream.
8. Plug the treadmill into the electrical outlet.
9. Spread the silicon by running the treadmill at 1 mph and
gently step on the belt from left to right.
10. Run on the treadmill for a few minutes and allow the silicon
to properly soak into the belt.
A well lubricated deck will ensure longevity of your treadmill in addition to providing you with
the optimal performance.
P. 4
© 2006 Sportcraft, Ltd.
1
2
5
4
3
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
22
21
25
24
23
28
27
26
29
9-3-04-060FH17
9-3-04-005FH01
9-3-04-005FH02
9-3-04-032FH04
9-3-04-032FH03
9-3-04-001FH32
9-3-04-041FH24
9-3-04-001FH30
9-3-04-001FH27
9-3-04-020FH16
9-3-04-001FH14
9-3-04-001FH13
9-3-04-003FH06
9-3-04-001FH1
1
9-3-04-032FH05
9-3-04-001FH09
9-3-04-001FH07
9-3-04-001FH06
9-3-04-055FH14
9-3-04-005FH05
9-3-04-032FH07
9-3-04-005FH04
9-3-04-055FH22
9-3-04-001FH05
9-3-04-005FH03
9-3-04-001FH08
9-3-04-005FH06
9-3-04-032FH09
9-3-04-032FH10
PARTS IDENTIFIER
(PRE-INST
ALLED)
ON/OFF SWITCH
(1 EA)
MAIN FRAME
ASSEMBL
Y
(1 EA)
CONTROL
P
ANEL
(1 EA)
SIDE RAIL
TUBE
(2 EA)
HAND RAIL
TUBE
(1 EA)
LA
TCH
(1 EA)
FRONT
WHEEL
(2 EA)
SILICONE
(1 EA)
PLASTIC END CAP
FOR
SIDE RAIL
TUBE (4 EA)
SAFETY
KEY
(1 EA)
5 MM
ALLEN KEY
(1 EA)
10 MM WRENCH
(1 EA)
INCLINE
ADJUSTER
WITH P
ADS (2 EA)
FRAME FOOTP
AD
(2 EA)
D-SHAPE CASTER FRAME
(1 EA)
6 MM SPRING W
ASHER
(2 EA)
6 X 55 MM
ALLEN KEY
BOL
T (2 EA)
10 MM HEX BOL
T
(8 EA)
(PRE-INST
ALLED)
(PRE-INST
ALLED)
(PRE-INST
ALLED)
(PRE-INST
ALLED)
(PRE-INST
ALLED)
(PRE-INST
ALLED)
(PRE-INST
ALLED)
ALLEN KEY
HOLDER
(1 EA)
REAR ROLLER COVER
- LEFT
(1 EA)
BOTT
OM MOT
OR COVER
(1 EA)
(PRE-INST
ALLED)
TOP
MOT
OR COVER
(1 EA)
(PRE-INST
ALLED)
6 X 90 MM
ALLEN
KEY
BOL
T (2 EA)
4 X 16 MM
TAIL
CUT
SCREW BLACK (4 EA)
12A
BREAKER
(1 EA)
(PRE-INST
ALLED)
10 MM SPRING W
ASHER
(8 EA)
(PRE-INST
ALLED)
REAR ROLLER COVER
- RIGHT
(1 EA)
TOOLS REQUIRED FOR
ASSEMBL
Y:
· Phillips and
Slotted
Head
Screwdrivers
(or
Power
Driver)
- not
included
· W
rench - included ·
Allen Key - included
Terminology Key:
- the front
= the end with the motor and cover
.
- the rear
= the end away from the motor
.
- the top
= the part you walk/run on.
- right/left
= right or left as standing on the treadmill.
VER
TICAL
ARM
- LEFT
VER
TICAL
ARM
- RIGHT
(PRE-INST
ALLED)
(PRE-INST
ALLED)
Meijer.com