background image

X

X

X

X

X

X

16"

15-1/4"

2x4 Joist Header

X

X

16"

Nail 2x4 joist headers and

floor joist to 4x4.

It is important that the floor be level and square. Square the floor as follows: before nailing the
flooring, measure the floor diagonally (corner to corner). Then measure the opposite corners.

These measurements will be the same if the floor is square.

2x4 Floor Joist
spaced 16" o.c.

2x4 Joist Header

4x4 Treated Runners

Flooring

Outside Measurement

2.

Cut 2x4-12' floor joist to 11'-9". Treated lumber may be thicker than 1-1/2". Take this into

account when cutting the length of floor joists. Shorten joist measurements if necessary to
obtain 12'-0" building width.

1.

Cut (2) two 2x4 joist headers to 16' - 0". Layout for 16" on center joist spacing. 'X' marks

where floor joist will be placed.

Material Description

12' x 16' shed

2x4 Joist Headers

2 pcs.

16'

2x4 Floor Joist

13 pcs.

12'

4x4 Treated Runners

8 pcs.

8'

Flooring 5/8" or 3/4"

6 pcs. 4x8

Screw Floor Nails

2 lb.

8d

Galv. Box Nails

2 lb.

16d

16' - 0"  Floor Length

12' - 0" Wide

Constructing Details for Deluxe Floor System

Deluxe floors include 4x4 runners, standard floors do not

Check local building codes in your area, the construction may have to change. For a concrete slab,

install sill sealer as a moisture barrier between the concrete and the wall plates. Foam sill sealer can
be purchased at home centers  in rolls 3-1/2" or wider.

Содержание the Riviera





















Отзывы: