Best Barns Millcreek страница 18 Скачать руководство пользователя | Manualshive

Страница: 18 / 24

background image

DETAIL 'D'

.

.

.

.

.

.

.

.

:

:

:

:

:

:

:

:

:

:

:

1x4 Trim

Step 17

Set Rear and Front Gables

WARNING: The gable ends are heavy
and awkward. You'll need helpers to lift
and set gables in place.

1.

Install the rear gable on the rear wall. The

siding on the gable must extend over the 1x4
trim board, not behind it. See detail 'D' below.

Nail bottom gable to loft flooring. Use 10d

sinker nails spaced evenly in stud openings.

2.

Install (2) two 61" long 1x4 gable trim flush with the top edge of the gable. Install the

ends with blue marks together. Install trim with 8d galvanized nails spaced 12" apart.

3.

Install (2) two 42-1/2" long 1x4 gable trim

flush with the side edge of the gable.

4.

Install the front gable. Do Not apply trim.

1x4 Trim

Bottom Edge of Gable Siding

Overlaps Top Wall Trim; nail

with 8d galvanized box nails.

«
...
16
17
18
19
20
...
»

Содержание Millcreek

























Отзывы:

Нет отзывов

Похожие инструкции для Millcreek

03DTSHRA1008FGC42TW-V1

Бренд: Mercia Garden Products Страницы: 14

Lillevilla 100 C-3

Бренд: Luoman Страницы: 14

Бренд: Sentry Buildings Страницы: 28

Бренд: Handy Home Products Страницы: 65

Бренд: Karibu Страницы: 28

Бренд: Gartenpro Страницы: 41

Бренд: Palmako Страницы: 68

CB128-SLIDER-METAL-BEV

Бренд: OLT Страницы: 45

Бренд: Palmako Страницы: 54

shedmaster GABLE 8' x 12'

Бренд: Backyard Products Страницы: 55

Бренд: Palmako Страницы: 29

Бренд: Mercia Garden Products Страницы: 9

Бренд: Tiger Страницы: 24

TIGERFLEX Copia

Бренд: Tiger Страницы: 32

Бренд: Palmako Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды