Best Barns Millcreek Скачать руководство пользователя | Manualshive

Страница: 11 / 24

background image

If you want the barn doors in the center of the front wall, go to Step 9B.

:

:

:

:

:

:

75" Long 2x6

OSB Filler

3.

Go to Step 10A.

3.

Go to Step 10B.

X

X

X

X

19-3/4"

32-1/2"

2x4 - 68-1/2

Boards

2x4 - 6' Board (Door Spacer)

19-3/4"

..

..

.

. .

Step 8

Assemble Door Header

Assemble door header using (2) two 75" long 2x6 boards and a 75" OSB filler
panel. Apply wood glue with a brush between OSB and boards. Nail header
together with 10d coated sinkers. Use (12) twelve nails on each side.

19-3/4"

24"

Bottom Wall Plate Assembly

Step 9A

Assemble Bottom Wall Plate (doors offset)

Step 9B

Assemble Bottom Wall Plate (doors centered)

56-1/2" To Door Spacer

Door Spacer

1.

Butt (2) two 68-1/2" boards together to make bottom wall plate. Secure bottom plate with

a 2x4-6' board (used as door spacer) installed 56-1/2" from the end of the 2x4 wall plate.
Secure with (4) four 2-1/2" wood screws.

2.

Mark locations for the wall studs with 'X' marks.

1.

Butt (2) two 68-1/2" boards together. Center a 2x4-6' board (used as door spacer) on top and

screw the boards together using (4) four 2-1/2" wood screws.

2.

Mark stud spacing as shown below.

«
...
9
10
11
12
13
...
»

Содержание Millcreek

























Отзывы:

Нет отзывов

Похожие инструкции для Millcreek

Бренд: G21 Страницы: 32

Бренд: Palmako Страницы: 21

Бренд: Palmako Страницы: 46

Бренд: Palmako Страницы: 45

Бренд: Palmako Страницы: 55

Бренд: Palmako Страницы: 55

Бренд: Palmako Страницы: 56

Бренд: Palmako Страницы: 65

Бренд: Sojag Страницы: 36

Бренд: Universo Consumer Products Страницы: 20

Бренд: Palmako Страницы: 104

Бренд: Palmako Страницы: 35

Бренд: Karibu Страницы: 34

Бренд: Hanover Страницы: 15

SpaceSaver SS124-SLIDER-METAL-FJ

Бренд: OLT Страницы: 39

Sussex Summerhouse

Бренд: Walton Страницы: 4

Бренд: Palmako Страницы: 76

Бренд: Forest garden Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды