manualshive.com logo in svg

BEST ACCESS SYSTEMS 9KQ, Руководство по установке, Страница: 8 / 16

Поделиться
Скачать
BEST ACCESS SYSTEMS 9KQ Скачать руководство пользователя страница 8

Installation Instructions for Wi-Q™ Technology 9KQ Cylindrical Locks

8

Installing the lock

BEST ACCESS SYSTEMS

a Product Group of dormakaba USA Inc.

9

Install lock chassis and engage 
retractor in latch

From the outside of the door, insert the lock chassis 
into the 2 1/8

″

 chassis hole, routing the motor wire 

through the notch.

Caution:  

Make sure that the latch tube prongs 

engage the chassis frame and that the latch 
tailpiece engages the retractor.

10

Install the trim hole insert, bushing, 
and hub washer on outside of door

1  On the outside of the door, insert the trim hole insert 

into the upper trim hole, as shown in Figure 10.

2  Insert the bushing into the harness hole.

3  Slide a hub washer over the chassis sleeve so it rests on 

the hub.

Inside of door

 Figure 9

Installing the lock chassis and engaging the 
retractor in the latch

Latch tube
prong

Retractor

Latch 
tailpiece

Chassis

Chassis frame

Latch tube
prong

Notch

Outside of door

 Figure 10 Installing the outside trim hole insert, 

bushing, and hub washer

Trim hole insert

Bushing

Hub washer

Hub

Содержание 9KQ

















Отзывы:

Нет отзывов