BEST ACCESS SYSTEMS 9KQ Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 16

BEST ACCESS SYSTEMS 9KQ Скачать руководство пользователя страница 2

Installation Instructions for Wi-Q™ Technology 9KQ Cylindrical Locks

2

Preparing the door and door jamb

BEST ACCESS SYSTEMS

a Product Group of dormakaba USA Inc.

1

Position template and mark drill points

Note: If the door is a fabricated hollow metal door,
determine whether it is properly reinforced to support
the lock. If door reinforcement is not adequate, consult
the door manufacturer for information on proper rein-
forcement. For dimensions for preparing metal doors,
see the

Q01 and G02 Templates—Installation Specifi-

cations for 93KQ Cylindrical Locks

.

Note: If the door is a LH or RH door, mark the inside of
the door. If the door is a LHRB or RHRB door, mark the
outside of the door.

For uncut doors and frames

1 Measure and mark the horizontal centerline of the

lever (the centerline for the chassis hole) on the door
and door jamb. Mark the vertical centerline of the door
edge.

Note: The recommended height from the floor to the
centerline of the crossbore or chassis hole is 38”

.

2 Fold

the

Q05 Template—Installation Template for

93KQ Cylindrical Locks

on the dashed line and carefully

place it in position on the high side of the door bevel.

Note: For steel frame applications, align the template’s
horizontal centerline for the latch with the horizontal
centerline of the frame’s strike preparation.

3 Tape the template to the door.

4 Center punch the necessary drill points. Refer to the

instructions on the template.

For doors with standard cylindrical preparation

1 Fold

the

Q05 Template—Installation Template for

93KQ Cylindrical Locks

on the dashed line. Looking

through the hole from the opposite side of the door,
align the template so that you see the template
outline of the 2 1/8

″

diameter chassis hole.

2 Tape the template to the door.

3 Center punch the necessary drill points. Refer to the

instructions on the template.

Figure 1

Positioning the template

Installation template

Centerline of lock

«
1
2
3
4
...
»

Содержание 9KQ

















Отзывы:

Нет отзывов