Bertazzoni Model P910 1 PRO X, Инструкция по эксплуатации

Страница: 5 / 12

5
WARNING: If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
When the connection is made directly with the electricity supply:
- Make sure that there is a device to disconnect the appliance from the mains with a contact opening distance sufficient for complete
disconnection in category III overvoltage conditions.
- Place a single-pole switch between the appliance and the electricity supply. The switch must be of a suitable charge for the appliance
with a minimum opening between the contacts of 3 mm.
- Remember that the earth wire must not be interrupted by the switch.
- Alternatively the electrical connection can also be protected by a differential switch of high sensitivity.
- You are strongly advised to fix the special yellow-green earth wire to an efficient earthing system
BEFORE LEAVING
When the installation is complete, always check for gas leaks using a soapy solution. Never use a flame to make this check.
Ignite all burners on high flame to ensure correct operation of gas valves, burners and ignition. Turn gas taps to low flame position and
observe each burner to ensure they ignite completely at all ports and that the flame is stable. Conduct these checks for each burner
individually and concurrently.
When satisfied with the hotplate, please instruct the user on the correct method of operation. In case the appliance fails to operate
correctly after all checks have been carried out, please call the Bertazzoni Service Centre.
USE AND MAINTENANCE MANUAL
IMPORTANT SAFETY INSTRUCTIONS

DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE APPLIANCE STORAGE DRAWER OR NEAR THIS APPLIANCE.

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

DO NOT STORE OR USE FLAMMABLE LIQUIDS OR ITEMS IN THE VICINITY OF THIS APPLIANCE.

DO NOT MODIFY THIS APPLIANCE.

WHERE THIS APPLIANCE IS INSTALLED IN MARINE CRAFT OR IN CARAVANS, IT SHALL NOT BE USED AS A SPACE
HEATER.

WARNING: SERVICING SHOULD BE CARRIED OUT ONLY BY AUTHORISED PERSONNEL.

This appliance is not intended for use by persons (including children) with reduced mental or motorial capacities or who have no
experience and knowledge unless under supervision or instructed on use of the appliance by a person responsible for their safety.
Children must be watched to ensure that they do not play with the appliance
DESCRIPTION OF HOBS

GAS HOB TYPE P680 , see Fig. 12 - Electrical Diagram A

GAS HOB TYPE P910 , see Fig. 13 - Electrical Diagram B
DESCRIPTIVE CAPTION FOR HOB
CAPTION FOR ELECTRICAL DIAGRAM
(Figs. 12 13) (Diagrams A B)
1 Auxiliary burner 1 Electric panel
2 Semi-rapid burner 2 Lighter button
3 Rapid burner 3 Ignition device
4 Dual burner 4 Lighting plugs
5 Front left burner knob L Brown (phase)
6 Front right burner knob N Blue (neutral)
7 Back left burner knob ‘
’
Yellow/Green (earth)
8 Back right burner knob
9 Central burner knob
10 Front central burner knob
11 Back central burner knob
USE OF THE BURNERS
On the control panel above every knob there is a diagram which indicates which burner the knob in question refers to. The burners can
be turned on in several ways according to the type of appliance and its individual features:
- Manual “On” switch ( this is always possible even if the electric current is cut off ): Turn the knob corresponding to the selected
burner in an anticlockwise direction so that the knob is at MAXIMUM (this corresponds to a large flame) and then put a lit match to the
burner.
- Electric “On” switch: Turn the knob corresponding to the selected burner in an anticlockwise direction so that the knob is at
MAXIMUM (this corresponds to a large flame) and then press the lighter button and let it go as soon as the burner is alight..