background image

 

7

 

Changing the parts

 

Before carrying out any maintenance work, disconnect the appliance from the gas and electric supply.  

To replace different components such as  burners, taps and electrical parts you must take out the hob from the kitchen unit by releasing 
the fixing hooks, unscrew the fixing screws of the burners on the work top, unscrew the fixing nuts of the electric plates which are visible 
on the lower part of the hob and remove the worktop in order to carry out the replacement of the defective parts

NOTE: If the taps need replacing you also need to unscrew the two fixing screws of the gas ramp at the bottom of the hob which are 
found on the upper part of the latter.  
For appliances equipped with automatic “ON” switches you must dismantle the “ON” switch chain before replacing the taps. 
You are advised to change the seal on the tap every time you replace a tap in order to ensure a perfect hold between the body and 
ramp. 

WARNING

: The power cord supplied with the appliance is connected to the appliance with a type 

Y

 connection (in compliance with 

standards EN 60335-1, EN 60335-2-6 and subsequent amendments) for which it must be replaced by the manufacturer or its service 
agent or a similarly qualified person in order to avoid a hazard. 
In the event of wear or damage to the mains cable, replace it following the indications shown below in table n°3: 
 
TABLE  N° 3: Types and sections of the electric mains cable for hobs 

Dimensions of hob 

Type of hob 

Type/ section of mains cable  

59 x 50 cm. 
86 x 50 cm. 

gas burners 

     H05RR-F  3x0,75 mm2 

 

WARNING: If you replace the electric mains cable the installer must have the earth conductor about 2 cm longer than the phase 
conductors and must also take heed of the warnings regarding electric connection. 

 

Oiling the taps: (This must be carried out by qualified staff from a technical assistance centre)  

If a tap becomes difficult to move you must oil the tap, without delay, following the instructions given below:  
1) Dismantle the main part of the tap by unscrewing the two screws that can be found on the bar of the tap itself. (Fig. 11) 
2) Take out and clean the holding cone and its setting with a cloth soaked in diluent.   
3) Oil the cone lightly with the special oil. 
4) Insert the cone, move it a few times, take it out again, remove the excess oil and make sure that the areas where the gas flows are 
not obstructed.  
5) Reassemble all the pieces in the reverse order to that followed for the dismantling and check that the tap is working properly. 
 

After-sales technical service and spare parts 

 
Before leaving the factory, this appliance was tested and adjusted by specialist skilled staff to give the best 
operating results. Any subsequent necessary repairs or adjustments must be carried out with the greatest 
care and attention by authorised personnel. For this reason, we strongly advise you contact the 

Bertazzoni 

Service Center

, specifying the nature of the problem, the model of the equipment and the serial number. 

This data is provided on the data label adhered to the base of the appliance and on the duplicate data label. 
Always use original 

Bertazzoni spare parts

.

 

 

 
 

 

BERTAZZONI GROUP 

ABN 38 069 686 326

 

650 Bridge Road, Richmond, Victoria  3121 

Service & Spare Parts: 1300 748 308 

Bertazzoni After Sales Service - P.O. Box 543 SOMERTON VIC 3061 

Email:  

[email protected]

 

 
 
 

Содержание Model P910 1 PRO X













Отзывы: