BERRIDGE TZ-21 Скачать руководство пользователя | Manualshive

Страница: 9 / 11

background image

Safety

Minimum Safety Practices:

It is important to abide by normal safety rules when operating Berridge
portable roll formers. While Berridge recommends the following
minimum safety practices, the company accepts no responsibility
for personal injury or property damage incurred while operating the
machine.

1. Make sure electrical outlet is grounded.
2. Do not operate machine in rain or standing water.
3. Make sure electrical cord is free of cuts and/or exposed wire.
4. Keep hands and clothing out of the rolls and the shear blade.
5. Keep wheels locked on the machine except when necessary to

physically move it.

6. Do not stand under coil when loading or unloading machine.
7. Do not operate machine with Plexiglas panels removed.

BERRIDGE
MANUFACTURING
COMPANY

2201 Rudeloff Road

Seguin, TX 78155

Sales: (800) 669-0009

Roll Former Dept: (830) 303-0811

Fax: (830) 303-0530

www.berridge.com

«
...
7
8
9
10
11
»

Содержание TZ-21












Отзывы:

Нет отзывов

Похожие инструкции для TZ-21

Бренд: MacDon Страницы: 17

Бренд: Olympus Страницы: 50

Бренд: VAHVA Страницы: 19

Бренд: iGuzzini Страницы: 20

Бренд: NARGESA Страницы: 50

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: made for movement Страницы: 51

Бренд: Campbell Страницы: 2

Бренд: Xebex Fitness Страницы: 15

Бренд: qeedo Страницы: 2

Бренд: Radial Engineering Страницы: 2

Бренд: Radial Engineering Страницы: 2

Бренд: quadient Страницы: 188

Бренд: Radarsign Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды