Berkeley S.A.E. Скачать руководство пользователя страница 3

F00636

Page 3

Safety First

General Information

READ AND FOLLOW 
SAFETY INSTRUCTIONS!

This is the safety alert symbol.

When you see this

symbol on your pump or in this manual, look for one
of the following signal words and be alert to the
potential for personal injury:

DANGER

warns about hazards that 

will

cause

serious personal injury, death or major property
damage if ignored.

WARNING

warns about hazards that 

will 

or 

can

cause serious personal injury, death or major
property damage if ignored.

CAUTION

warns about hazards that 

will

or 

can

cause minor personal injury or property damage
if ignored.

The label 

NOTICE

indicates special instructions

which are important but not related to hazards.

Carefully read and follow all safety instructions in
this manual and on pump.

Keep safety labels in good condition. 
Replace missing or damaged safety labels.

General Safety

Do not allow pump, piping, or any other system com-
ponent containing water to freeze. Freezing may
damage system, leading to injury or flooding. Allowing
pump or system components to freeze will void
warranty.

Pump approved liquids only with this pump.

Periodically inspect pump and system components.

Wear safety glasses at all times when working on
pumps.

Keep work area clean, uncluttered and properly lighted;
store properly all unused tools and equipment.

Keep visitors at a safe distance from the work areas.

WARNING

Rotating parts. Can catch
hands, feet, or clothing.

Stay clear of equipment and
keep shields in place while
pump is running. 

Stop motor or engine before
servicing pump.

Read owner’s manual before
using equipment.

Содержание S.A.E.





























Отзывы: