Berkeley S.A.E. Скачать руководство пользователя страница 27

F00636

Page 27

Warranty

Berkeley

LIMITED WARRANTY

BERKELEY warrants to the original consumer purchaser (“Purchaser” or “You”) of the products listed below,
that they will be free from defects in material and workmanship for the Warranty Period shown below. 

Product

Warranty Period

Water Systems:

Water Systems Products — jet pumps,

whichever occurs first:

small centrifugal pumps, submersible pumps

12 months from date of original installation, or

and related accessories

18 months from date of manufacture

Pro-Source

TM

Composite Tanks

5 years from date of original installation

Pro-Source

TM

Steel Pressure Tanks

5 years from date of original installation

Pro-Source

TM

Epoxy-Lined Tanks

3 years from date of original installation

Sump/Sewage/Effluent Products

12 months from date of original installation, or
18 months from date of manufacture

Agricultural/Commercial:

Centrifugals – close-coupled motor drive, frame 

12 months from date of original installation, or

mount, SAE mount, engine drive, VMS, SSCX, 

24 months from date of manufacture

SSHM

Submersible Turbines, 6” diameter and larger

12 months from date of original installation, or
24 months from date of manufacture

Our limited warranty will not apply to any product that, in our sole judgement, has been subject to negligence,
misapplication, improper installation, or improper maintenance. Without limiting the foregoing, operating a
three phase motor with single phase power through a phase converter will void the warranty. Note also that 
three phase motors must be protected by three-leg, ambient compensated, extra-quick trip overload relays of
the recommended size or the warranty is void.

Your only remedy, and BERKELEY’s only duty, is that BERKELEY repair or replace defective products (at
BERKELEY’s choice). You must pay all labor and shipping charges associated with this warranty and must
request warranty service through the installing dealer as soon as a problem is discovered. No request for
service will be accepted if received after the Warranty Period has expired. This warranty is not transferable.

BERKELEY SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER.

THE FOREGOING LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE FOREGOING WARRANTIES
SHALL NOT EXTEND BEYOND THE DURATION EXPRESSLY PROVIDED HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on
the duration of an implied warranty, so the above limitations or exclusions may not apply to You. This warranty
gives You specific legal rights and You may also have other rights which vary from state to state.

This warranty supersedes and replaces all previous warranty publications.

In the U.S.: BERKELEY, 293 Wright St., Delavan, WI  53115

In Canada: 269 Trillium Dr., Kitchener, Ontario N2G 4W5

Содержание S.A.E.





























Отзывы: